Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Panasonic Dateigröße: 1.67 mb Dateiname: AWRP605.PDF Unterrichtssprache:

This adjustment is not necessary when component signals have been set as the video input signals. 1. Select the pan-tilt head CONTROL/PREVIEW MONITOR OUT SEL button. 2. Connect the video switcher or other equipments to the VIDEO/Y OUT connector on the main unit that corresponds to the currently selected pan-tilt head system, and connect a color monitor to the video output connector on the video switcher or other equipments. 3. Press the MODE button to establish the BAR mode and switch the output signals from the convertible camera to color bar signals. 4. Press the MENU button, turn the menu setting control (main), and set it so that the G/L SETTING item appears at the top of the LCD panel. 5. Press the OK button. The following item appears on the LCD panel. 6. Turn the menu setting control (main), and set it so that the following item appears on the LCD panel. 7. Output both the color bar signals (signals from inside the switcher or other equipments) serving as the reference and the color bar signals from the camera to the color monitor. 8. Align the phase of the color bar signals from the camera with the phase of the color bar signals serving as the reference. Use the menu setting control (L) to adjust the phase in 90-degree increments and then the menu setting control (R) to make fine adjustments. SSCC PPHHAASSEE CCOOAARRSSEE::11 FFIINNEE:: ±±00 CCAABBLLEE LLEENNGGTTHH SSHHOORRTT GG//LL SSEETTTTIINNGG n OOKK KKeeyy Subcarrier phase adjustment WhiteYellowCyanGreenMagentaRedBlueBlack 9. Select the next pan-tilt head system using the CONTROL/PREVIEW MONITOR OUT SEL button, and continue adjusting the subcarrier phase in each system concerned. 4•6 5 system using the CONTROL/PREVIEW MONITOR OUT SEL AUX1 2 3 4 5 TALLY TRACING MEMORY LAMP MENU LIMIT OFF LIMIT ON FULLEMPTY OK LCD CONTRAST CAMERA CONTROL START POINTR/B GAIN/PED WHITE BAL AWC GAIN MODE CLOSE WIDE NEAR DATA S ET TR/PSET M.LOCK MEMORY IRIS IRIS IRIS OPEN ZOOM TELE FOCUS FAR CALL INCOM LEVEL FOCUS OPEN FAR TELE OFF ON OPERATE WIDE ZOOM/FOCUS/IRIS ABC AT W A B NG OK START/STOP RESTORE RESET DEF WIP H/F EXT ND OPTION PAN/TILT SETCAMERA CONTROL TRACING/PRESET MEMORY IRIS SPEED FOCUS BAR CAM TR PSET LOW HIGH AUTO MANU AUTO MANU LOCK 11 12 13 14 15 16 17 18 19 20 UP PRIORITY1 2 3 4 5 6 7 8 9 10 21 22 23 24 25 26 27 28 29 130 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DOWN FARNEAR PAN/TILT/FOCUS/IRIS L R CLOSE NEAR OPENCLOSE 4883 Color bar signals from the camera Partition line Color bar signals from the switcher or other equipments 27 Operation $ Total pedestal adjustment When more than one camera is to be used, the black level 5 (pedestal level) of the pictures shot by each of the cameras must be brought into alignment. 1. Select the pan-tilt head system using the CONTROL/PREVIEW MONITOR OUT SEL button. 2. Connect a waveform monitor to the VIDEO/Y OUT connector on the main unit that corresponds to the pan- tilt head system currently selected. 3. Press the IRIS button to establish the MANU mode (the IRIS button’s lamp now goes off), and use the FOCUS/IRIS dial to close the lens iris. 4. Press the R/B GAIN/PED button, and set it so that the following item appears on the LCD panel. P PPE EED DDE EES SST TTA AAL LL T TTO OOT TTA AAL LL ± ±±0 00 R RR: ::± ±±0 00 B BB: ::± ±±0 00 5. Use the menu setting control (main) to adjust the black level to 5 IRE (0.035V) or 7.5 IRE (0.050V). The black level should be adjusted to the same level of equipments of the system. CONTROL/PREVIEW MONITOR OUT SEL AUX1 2 3 4 5 TALLY TRACING MEMORY LAMP MENU LIMIT OFF LIMIT ON FULLEMPTY OK LCD CONTRAST CAMERA CONTROL START POINTR/B GAIN/PED WHITE BAL AWC GAIN MODE CLOSE WIDE NEAR DATA S E T TR/PSET M.LOCK MEMORY IRIS IRIS IRIS OPEN ZOOM TELE FOCUS FAR CALL INCOM LEVEL FOCUS OPEN FAR TELE OFF ON OPERATE WIDE ZOOM/FOCUS/IRIS ABC ATW A B NG OK START/STOP RESTORE RESET DEF WIP H/F EXT ND OPTION PAN/TILT SETCAMERA CONTROL TRACING/PRESET MEMORY IRIS SPEED PRIORITY FOCUS BAR CAM TR PSET LOW HIGH AUTO MANU AUTO MANU LOCK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 130 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DOWN PAN/TILT/FOCUS/IRIS UP L R CLOSE NEAR OPEN FAR CLOSE NEAR 43 3 (3) 1 5 IRE (0.035V) or 7.5 IRE (0.050V) 6. Select the next pan-tilt head system using the CONTROL/PREVIEW MONITOR OUT SEL button, and continue adjusting the black level for each system concerned. 28 Operation $ White balance adjustment The white balance must be adjusted when the equipment is used for the first time, when it has not been used for a prolonged time or when the lighting conditions or brightness has changed. The white balance conditions can be entered in advance into channels A and B. If the equipment is to be used under conditions which are identical to the entered settings, it means that no further adjustment need be undertaken since the white balance will be set simply by pressing the WHITE BAL A button or B button once the whit...

Herunterladen

Geben Sie zwei Ziffern: