Stimmen - 4, Durchschnittliche Bewertung: 4.8 ( )

Hersteller: Broan Dateigröße: 1.13 mb Dateiname: Unterrichtssprache:

Mounting brackets in factory-shipped position. (Outlet parallel to joists.) (New construction) ..y..y..y ..y..y..y..y 12." 10 3/ 4" to 11 3/ 4" ..y..y..y ..y..y..y 12." .-20 hex nuts secure mounting brackets to housing. Loosen and re-tighten or remove and replace nuts as necessary for desired mounting bracket position. Mounting brackets flipped over and mounted to outlet sides of housing. (Outlet parallel to joists.) (Existing construction) Mounting brackets mounted to outlet sides of housing. (Outlet perpendicular to joists.) (New construction) Mounting brackets flipped over and mounted to top of sides of housing. (Outlet parallel to joists.) (New or existing construction) ..y..y ..y..y..y..y 12." 11/ 2" to 21/ 2" Mounting brackets flipped over to give approx. 1” more clearance. (Outlet parallel to joists.) (New construction) Mounting brackets mounted to top of sides of housing. (Outlet parallel to joists.) (New or existing construction) BLOWER DISCHARGE POSITIONS WIRING PLATE POSITION Wiring plate mounts to side or top of housing. HORIZONTAL POWER CABLE CONNECTION VERTICAL POWER CABLE CONNECTION Blower and duct connector in straight through discharge position. (Factory shipped) DUCT CONNECTOR DUCT CONNECTOR Blower and duct connector in right angle discharge position. BLOWER BLOWER Change blower & duct connector positions for right angle discharge. DUCTING (Right angle blower discharge) Typical ductwork connection to a ventilator converted to right angle discharge. ROOF CAP ROUND DUCT* WARNING: To reduce the risk of electric shock, disconnect from power supply before servicing. To clean blower assembly: Remove access panel, unplug blower from housing, remove blower mounting nuts, and carefully remove blower from housing. Use appropriate vacuum attachment or a soft cloth and mild soap or detergent to clean blower discharge area and wheel. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure blower assembly is completely dry before reinstalling. Motor is permanently lubricated. Do not oil or disassemble motor. USE AND CARE Ventilator is designed for continuous operation. If desired, it may be controlled using an on/off switch or an electronic, variable speed control. Follow wiring instructions packed with control, and adhere to all local and state codes, and the National Electrical Code. * L100L & L150L use 6” round duct. L200L, L250L, & L300L use 8” round duct. MODELS L100L • L150L • L200L • L250L • L300L Page 4 SERVICE PARTS SERVICE PARTS KEY NO. PART NO. DESCRIPTION 1 97014735 Housing Assembly (L100L & L150L) 97014736 Housing Assembly (L200L, L250L, & L300L) 2 97014728 Mounting Bracket (2 req.) 3 97014760 Damper Assembly (6” dia.) 97014761 Damper Assembly (8” dia.) 4 99390098 Duct Connector (6” dia.) 99390099 Duct Connector (8” dia.) 5 99150415 Screw, 8-18 x . (12 req.)* 6 98005513 Wire Box Cover 7 99400035 Strain Relief Bushing 8 98005512 Wiring Plate 9 99150471 Ground Screw, 10-32 x . (2 req.) 10 97014774 Scroll Assembly (L100L & L150L) 97014775 Scroll Assembly (L200L, L250L, & L300L) 11 98009399 Inlet Ring 12 99110805 Blower Wheel 13 99080481 Motor (L100L) 99080482 Motor (L150L) 99...

Herunterladen

Geben Sie zwei Ziffern: