Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Crimestopper Security Products Dateigröße: 306.14 kb Dateiname: Unterrichtssprache:

2X then 12X 1X Green / 12X Orn. SILENT ARM #4 (Slnt) Press & Release 1X then 4X Orange / 4X SILENT DISARM #4 (Slnt) Press & Release 1X then 2X Green / 2X AUX #1 #3 (Aux.) Press & Release 1X then 3X NONE AUX #2 #4 (Slnt) Press/hold 2 sec. NO PAGE BACK Orange/Blinking Door Violation 1 Long / 2 Short Red / 3X Hood/Trunk Violation 1 Long / 2 Short Red / 3X Ignition Violation 1 Long / 4 Green / 5X Sensor Violation 1 Long / Yellow / Text Box: Text Box: Text Box: 15 OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter will be disabled. The red in- dash LED in the vehicle will begin to flash. After a short delay of 10-15 seconds to allow vehicle and electronics to stabilize the system will be completely armed. DISARMING To disarm the alarm and unlock the doors, press the #2 Button on any remote. lights will flash twice. The in-dash LED stops flashing dome light turns on (Optional). If the alarm is currently tripped, then the #2 Button will have to be pressed two times. The first press will only reset the trigger and the second press will Disarm the system. See “ARMED CYCLE RESET”. ALARM TRIGGERING If there is an intrusion into the vehicle such as an open door/hood/trunk, the alarm siren will sound and flash lights for 1 minute. This is known as a cycle. After the cycle, the system will automatically reset and continue protect the vehicle. If a door is left open then the unit will cycle for the Maximum of 5 minutes, reset, and continue protect the other un-tampered zones. ALARM CYCLE RESET If and when the alarm system is triggered, pressing on any remote will reset the unit’s cycle (lights, siren) condition without disarming it. Pressing a #2 button second time will Disarm/Unlock REMOTE PANIC PROTECTION To sound the alarm upon command (panic), #1 on any transmitter for at least until the siren sounds and lights flash. SILENT ARM/DISARM Press and release Button #4 the system without the flash will be your only confirmation REMOTE AUX. OUTPUT To activate an optional pop (if vehicle is #3 (AUX) on any pulse to activate other optional Text Box: 16 OPERATION SHOCK / IMPACT PROTECTION WITH PRE-WARNING Once the system is armed, if a low-level shock to the vehicle body is detected, the pre-warning sensor activates with 5 siren chirps and one light flash as a Warn-Away feature. If a hard impact to the vehicle go into a full trigger cycle for 20 seconds. Adjust the shock sensor as needed by turning the control knob clockwise or counter-clockwise to increase or decrease the sensitivity. Shock sensors will “settle in” over time and it may take a few tries over a few weeks to get the adjustment correct for your vehicle. We recommend a moderate adjustment where the vehicle is protected but it is not constantly triggering from the slightest vibration therefore creating a nuisance. ARMING WITHOUT SHOCK SENSOR To arm the alarm without Shock sensor protection, press Button #1 as normal then press and hold Button #4 (SLNT) for about 3 seconds until the unit flashes the lights 3 times indicating EMERGENCY OVERRIDE/DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to open door with the key, (activating the alarm), turn the ignition ON, press and hold the override/program until the disarms (about 7 seconds). The Alarm will disarm allowing you to operate the vehicle until you can repair/replace the remote transmitter. VALET MODE (VIA KEY or REMOTE) Turn the ignition on and press and hold the program the remote until lights chirps 3 times. in-dash LED turns on solid. Repeat the procedure mode. To activate Valet using the remote press both the #1 (Lock) 7 #2 (Unlock) 3 seconds when the system is disarmed. The system will chirp 3 times and the LED will turn off Lock/Unlock and AUX features will VALET mode. VALET PARK Mode (Using the Note: Valet Park mode is only remote transmitter. Valet park over the vehicle to a valet your vehicle, but alarm opened. To activate Valet seconds. 3 chirps will will hear 2 more Park. Repeat this PRIOR INTRUSION If the system be flashing will hear Text Box: 17 OPERATION PASSIVE ARMING / PASSIVE LOCK MODES If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly while counting down. If a door is reopened the countdown will reset and, the system will wait for the door or zone to close before starting 30 second countdown again. The unit will chirp once and flash the lights once. Doors will lock if passive locking is selected. May qualify for insurance discounts-check with your agent or proprietor. See Jumper Plug programming for J1 Passive Arm and J2 Passive Lock settings. DOME LIGHT ILLUMINATION (OPTIONAL) Th...

Herunterladen

Geben Sie zwei Ziffern: