Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
All remaining points above 568 will report as fire alarm points. Document 50934 Rev B 5/15/00 PN 50934:B To access Type Mode, press the MODE key followed by the 4-digit code 8973 and then press the [ENTER/STORE] key. The ADT-UDACT will display three digits. For example, initial entry will display 01 0. To access Type Mode, press the MODE key followed by the 4-digit code 8973 and then press the [ENTER/STORE] key. The ADT-UDACT will display three digits. For example, initial entry will display 01 0. 0 = Zone or point defined as fire alarm 1 = Disable zone or point report 2 = Zone or point defined as supervisory 3 = Zone or point defined as pull station 4 = Zone or point defined as heat detector 5 = Zone or point defined as waterflow 6 = Zone or point defined as duct detector 7 = Zone or point defined as flame sensor 8 = Zone or point defined as smoke zone (Use for group of addressable or conventional smoke detectors. Also use for addressable monitor modules monitoring conventional smoke detectors). 9 = Zone or point defined as burglary (Unimode 300/400 and ADT-MNNA) A = Zone or point defined as 24 hour non-burglary B = Zone or point defined as high temperature C = Zone or point defined as low temperature D = Zone or point defined as low water pressure E = Zone or point defined as low water level F = Zone or point defined as pump failure Factory default is all zones or points set to '0' for fire alarm. The '0' setting for zone reporting allows the mixing of types of devices on a single zone. To change the type definition of the zone or point from the factory default of 0, select 2 to F corresponding to the type of device(s) used (do not mix device types for these settings), or select 1 to disable alarm reporting of any zone or point. The digit entered will appear on the far right display. Next press the [ENTER/STORE] key. This stores the entry into E2 memory and increments to the next higher address. Use the UP, DOWN and 1st EVENT keys to move through the list of zones/points (refer to Appendices), similar to the method described in the programming section of this manual. To define all zones or points as fire alarm (return to original factory default settings) enter zone or point 999 and then press the [ENTER/STORE] key. The display will change to 01 0, indicating a return to the factory default settings. 4.2.1 Disabling of Zones or Points This feature is primarily used when system points have been defined as remote reset, acknowledge, silence or drill switches. Refer to the FACP technical manual for additional information. Activation of remote switches appear as alarms on the EIA485 bus. The ADT-UDACT will report these points as fire alarm points unless disabled in the Type Mode. Disabling zones or points also prohibits the activation (shorted or alarm activated condition) from being reported by the ADT-UDACT. Disabling of the zone or point does not affect the reporting of the zone or point trouble condition. Note: Type Mode '1' for zones 90-99, disables reports for these zones. To transmit reports for zones 90-99, use Type Mode entries of '0' or '2' through 'F'. Document 50934 Rev B 5/15/00 PN 50934:B 4.3 4.3 4.2.2 Zone or Point Supervisory A zone or point must be defined as supervisory to allow the ADT-UDACT to identify the correct report to transmit to the central station. Follow the programming instructions in the FACP manual to program a zone or point as supervisory. Next, program the zone or point as a code 2 for supervisory. Use the charts in Appendices to enter point and zone definitions. Note that the ADT-UDACT fire protection and reporting capabilities are inactive while in Type Mode. To get into the Troubleshoot Mode, press MODE 8768 and [ENTER/STORE]. .8768 spells TROU on a Touch-Tone® phone. Once in this mode, the ADT-UDACT will: • Transmit the 'UDACT off normal' message to the Central Station(s). • Continue to communicate any events not yet acknowledged at the Central Station prior to entering Troubleshoot Mode. The UP Arrow key, Down Arrow key and 1st EVENT keys do not function in this mode. Telephone Line Testing Pressing C for touchtone dialing or D for rotary dialing, followed by [ENTER/ STORE] causes seizure of the Primary phone line which in turn lights the red LED signifying Primary phone line active. After a delay of three seconds, the ADT-UDACT goes off hook to acquire a dial tone. The ADT-UDACT keypad may be used as a telephone touchpad for number dialing. Once the first digit is pressed, the display will move the C or D character one position to the left, while placing the digit to be dialed on the farthest right display position. Continue to press the phone numbers to be dialed. Successive depressions of the [ENTER/STORE] key hangs up and picks up the phone (places the phone on or off the hook). The secondary phone line may be tested by pressing the E key for touchtone dialing or the F key for rotary dialing and then following the same procedure used for the primary phone line. A han...