Login:
Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Anleitung ABC Office, modell Vector KT7105-A

Hersteller: ABC Office
Dateigröße: 532.12 kb
Dateiname: vector.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Locate the baseplate, cap nuts and washers. 2. Place the antenna on top of the baseplate, aligning the holes in the antenna base with the studs on the baseplate. Make sure that the power supply wire is in the channels of the antenna base and is not crushed between the antenna base and the baseplate. 3. Attach the washers and cap nuts to the bolts on the baseplate. DO NOT TIGHTEN. 4. Again make sure that the power wire is not crushed between the antenna base and baseplate and tighten the cap nuts with a .” wrench. 5. Connect the wire on the power supply to the power wire connected to the antenna. The wires will only connect in one direction. Text Box: 18 Inches Minimum Text Box: 3 Text Box: POSITIONING THE SYSTEM Text Box: 6. Position the system a minimum of 18” (Inches) from the doorframe and on the side closest to the door handle. 7. Cut the rubber molding to the length that will allow it to cover the wire from the wall to the system. You must cover the wire, using a metal pancake molding If the wire is in an area where it will be walked upon. 8. Insert the system power wire into the rubber pancake molding through the slit on the back. Using double sided tape fasten the rubber molding to the floor. 9. Plug the power supply into the closest outlet. We do not recommend using an extension cord for the system. 10. Test the system by placing one of the hard tags into the system. The system will beep approximately 1-1/2 seconds then reset. If a hard tag is held in the system it will continue to alarm. Text Box: 4 Text Box: Skirts Text Box: Shirts/Blouses/Jackets Text Box: 1. The tag should be visible to the customer. 2. Tag uniformly, it speeds up removal. 3. Tag near a price label. It assists in the removal. 4. Place the tag as high as possible when tagging silks & light or stretchy fabrics. 5. Except for leather goods we do not recommend locating the tag at the seams. The seams are easily cut open to remove the pin. 6. Avoid placing tags on waistbands, cuffs, hems or perimeters. They can be easily cut off. 7. Insert pins through the garment then gently push into the tag. 8. Never force the pin into the tag. 9. Never use bent pins. Text Box: TAGGING GUIDELINES Text Box: 5 Text Box: One Piece Bathing Suit Text Box: Bikini Bathing Suit Text Box: Pants Text Box: Dresses Text Box: TAGGING GUIDELINES Text Box: 6 Text Box: Purses Text Box: Belts Text Box: Tennis Shoes Text Box: Shoes Text Box: TAGGING GUIDELINES Text Box: 7 Text Box: 3. Remove the pin and hard tag from the detacher and store for future use. Text Box: 2. Remove the pin by holding the hard tag to the detacher and pulling straight up on the pin or garment. Text Box: 1. Place the hard tag into the detacher with the pin facing up. Text Box: REMOVING HARD TAG Text Box: 8 Text Box: THIS SPACE INTENTIONALLY LEFT BLANK Text Box: It is possible for the locking mechanism to become jammed when the pin is pulled extremely hard. It is possible to un-jam the pin so that you will be able to remove it when needed. The first step is to place the hard tag into the detacher then press on the head of the pin. This should release the pressure on the locks allowing you to remove the pin. If you are still unable to release the pin you...

Dieses Handbuch ist für folgende Modelle:
Überwachungstechnik - Vector 06502 (532.12 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien