Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Fostex Dateigröße: 1.38 mb Dateiname: d5_owners_manual.pdf Unterrichtssprache:

Recording a SKIP-ID at the Desired Point The undesired section can be skipped. During playback, a SKIP-ID can be recorded at the desired point. CM and narration can be skipped. The SKIP-ID is recorded at the start of the section to be skipped. When a SKIP-ID is found during playback, the D-5 will skip to the next S-ID. 1. Press the ID MODE button and select "WRITE-SKIP." ID MODE START WRITE ► SKIP END 2. Press the PLAY button. Playback from slightly before where SKIP-ID is to be recorded. If this point is overshot, press the « button. If the FINE CUE function (page 28) is used in place of the PLAY button, it can be recorded from a more accurate position. As it will automatically enter the S-ID recording mode after recording the SKIP-ID, the skip end point can be recorded after it. 3. Press the SET button at the desired position. SKIP-ID is recorded for about one second. No sound will be heard during this recording. ID MODE WRITE START SKIP END blink lit Recording SKIP-ID During a Recording Session Press the ID-MODE button while in the recording mode, select "SKIP," press the SET button and a SKIP-ID will be recorded. When executing a record/erase of an S-ID or SKIP-ID on a tape recorded with time code on another DAT recorder (D-10, D-30, etc.), please remember that time code continuity will be interrupted. The time code cannot be recorded by the D-5. D-5 Owner’s Manual 50 9-8. Erasing an Unnecessary SKIP-ID Unnecessary SKIP-ID can be erased during playback (it can also be erased in the stop mode). This cannot be erased in cassette tapes protected against mis-recording. 1. Switch off the AUTO-ID button. AUTO indicator will be extinguished. 2. Press the ID-MODE button and select "ERASE-SKIP." 3. SKIP-ID will be searched. Search for the SKIP-ID with CUE, press the PLAY button from beforehand of this SKIP-ID and enter the playback mode. 4. Press the SET button at where the ID mark is lit or where it ceases to be lit. ID MODE START ► SKIP ERASE END i blink When executing a record/erase of an S-ID or SKIP-ID on a tape recorded with time code on another DAT recorder (D-10, D-30, etc.), please remember that time code continuity will be interrupted. The time code cannot be recorded by the D-5. Buttons other than STOP will not work during sub-code recording arid erasing; D-5 Owner's Manual 51 Specifications Type Rotating head digital audio tape recorder Tape Speed 8.15mm/s (SP), 4.075mm/s (LP), 12.225mra/s (playback only, 1.5 TP) Recording Time (on standard 120' tape) SP mode: Max. 120 minutes (D-120 tape) LP mode: Max. 240 minutes (D-120 tape) Number of Channels 2 channel stereo Quantization Bit Number (*) 16 bit linear 12 bit non-linear Sampling Frequency (*) 48kHz 44.1kHz 32kHz (*) Sampling Frequency 48kHz 44.1kHz 32kHz 32kHz (*) Quantization Bit Number 16 bit 16 bit 16 bit 12 bit Tape Speed SP SP SP LP Analog Input O O X o Digital Input o o o o Analog Output o o o o Digital Output o o o o Error Correcting Method Modulation Type Emphasis Double encoded Reed Solomon code 8-10 conversion Analog recording: Fixed at OFF. Playback: Automatic switching. Head High output sendust head Standard record level -12dB Record/Playback Frequency Characteristics SP: 20Hz ~ 20kHz +/-ldB LP: 20Hz - 14.5kHz +/~ldB SN Ratio Dynamic Range Total Harmonic Distortion Wow Flutter Analog Input/Output Connectors Analog Audio Input Connector Standard input level Input impedance Analog Audio Output Connector Standard output level Output load impedance Headphone Output Connector Max. output level Output load impedance Higher than 90dB Higher than 90dB Less than 0.05% (1 kHz, standard recording level: +4dBu) Less than measurement limit (±0.001% WTD .PEAK) XLR-3-31 (Pin 1: GND, Pin 2: HOT, Pin 3: COLD) Switchable to +4dBu/-10dBV 10k n XLR-3-32 (Pin 1: GND, Pin 2: HOT, Pin 3: COLD) Switchable to 44dBu/-10dBV Higher than 600 H Stereo standard phone jack ^ 6mm Higher than 40mW (at 32 O) Higher than 8 fl D-5 Owner’s Manual 52 Digital Input/Output AES/EBU Digital Input Connector Input Format S/PDIF Digital Input Connector Input Format AES/EBU Digital Output Connector Output Format S/PDIF Digital Output Connector Output Format GPI Input (Parallel Remote Input Connector) Connector DIN 5 PIN Pin 1: GND Pin 2: STOP Pin 3: PLAY Pin 4: S-ID Search» Pin 5: S-ID Search « * PNP transistor input, Low Active (4.7k fl/5V Pull Up) XLR-3-31 (Pin 1: GND, Pin 2: HOT, Pin 3: COLD) Comply to AES/EBU specs. Optical Comply to IEC Consumer XLR-3-32 (Pin 1: GND, Pin 2: HOT, Pin 3: COLD) Comply to AES/EBU specs. Optical Comply to IEC Consumer Power Supply and Others Power Source/Power Consumption 120VAC 60Hz, 28W 230V- 50/60Hz, 28W Physical Dimensions 482 (W) x 134 (H) x 383.5 (D) mm Total Weight Approx. 6.8kg Accessories Wireless remote control unit (Model 8314) Batteries for remote control (UM-4; DEC-R03) Owner's Manual * Specifications and appearan...

Herunterladen

Geben Sie zwei Ziffern: