Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The VOYAGER Observation System is a supple1nentto standard rearview mirror systems, anlj will provide additional rearview visiun wherl installed and maintained properly. The VOYAGER Observation system is not intended in any way to be a substitute for careful, cautious, defensive driving or for the consistent adherence to all applicable traffic laws and motor safety regulations This product is not intended to be a substitute for rearview mirrors or for any other motor vehicle or boal equipment mandated by law FEATURES: AOC-75 CCD Camera 270,000 pixel image sensor 0.1 Lux sensitivity Automatic electronic iris provides a clearer, more consistent image in low and bright light Wide angle lens provides a broad viewing area Compact design and light weight ease installation in most vehicles, including large boats Durable, waterproof construction Built-in microphone for audio pickup Normal/mirror image switch on back of camera Wind deflector reduces build up of dirt on lens Waterproof cable connection AOM-70 Monochrome 7.0" Monitor Day/night switch Brightness and contrast controls Volume control Camera Dosition switch for a Danoramic view or a concentrated view Illuminated front panel Power/stand-by switch Internal speaker with external speaker jack CONTENTS OF 1 COMPLETE SYSTEM: AOC-75 CCD Camera: 1 -Camera 1 -Camera bracket 4 -Attachment screws with washers (M4x8) 1 -Wind deflector AOM-70 7.0" Monochrome Monitor' 1- 7.0" monitor 1 .Snap-on sun visor 1 -Monitor bracket 1 -Power harness with locking connector 1 -Range markers 4 -Thumb screws (MSx12) OCA.80 Cable: 1 -20 meter cable with waterproof connector. Oil, gas, grease resistant. UV stable Documents: 1-Operations manual Page lofl4 AOS.33 Operations Manual BEFORE IN5TALLATtON: 1. This system operates from 10 volts DC to 38 volts DC, negative ground 2. Please install this system according to the instructions in this manual. 3. Do not disassemble the camera or the monitor. This voids the warranty Disassembling the camera Will compromise the waterproof sea! 4. Connect the system to an ignition switched power source. Connection to a battery source will reduce battery life **WARNING** , .It) pTeve"1 e\~t:.1f\C'd\ "'\)t)C". DO NO'. oPEN '.HE tAON\TOR CA-SE. There are potentially lethal "Qltage~ in~ide the monitor. There are no user serviceable parts inside. If evidence of tampering is detected, the warranty will be considered void. 2. Keep monitor away from leaking water, rain, moisture etc, It is NOT waterproof, Any moisture inside the monitor could cause extensive damage, ~. Use \ne \numbscrews \0 moun\ \he rT1on'l\or to bracket, **CAUTION** '\ .DO NOT OPEN THE CAMERA CASE. This will break the camera's waterproof seal. If evidence of tampering is detected. the warranty will be considered void. 2. Do not molJnt the camera near the lower area of the vehicle (e.g. Bumper). This reduces the view of the camera and may cquse physical damage to tne camera 3. Use only the M4x8 bolts and washers to mount the camera INSTALlATION INSTRUCTIONS Acc.rs CAMERA 1 .Attach camera bracket (See Fig 1) to upper portio~ of vehicle. Attachment point must be s'urd)' enough 'I:> suppon camera and bracket. 2-Att~ch camera to bracket using M4x8 bolts provided. Adjust angle as indicated in figure 2 (Use rear bumper and back of vehicle as a reference point ~. W\tld dei\ectof ma~ 00 \m\a\\~.I"is Ue"~I:;\Of is desig"~d \0 r~t\ut:.e \ne bIJi\6 up 0\ du\;\, d\rt and mo\S\uTe on the camera lens (See Fig 3). AOM.70 MONiTOR 1. Att'i1ch monitor ins\;je veh\cle in a location conven\.!nt to the dri~er (e.g. center of dash, overhead or in dash). (See Fig 4) 2. Use a compression plate l!) attech the monitor bracket to the dash or overhead (See Fig 4). 3. Adjust !T\ounting a!)gle of the monitor to allow driver to easily view the screen from all seat positiOn$ (See Fig .5) . 4. If necessary, snap sun visor into groove on front face of monitor. Press a\l (4) sid.!s of the visor to ~nap it into pl-ace AOC-80 CABLE 1. The camera-to-cable connection ia waterproof. The cabJe-to-monitor connection is not waterproof. Be SlJre to orient the cable pr()perly. The cylindrical end attaches to the camera. The rectangular box end attaches to the monitor. (See figure 6) 2. Do not run the AOC-80 cable over sharp edges or corners. Do not kink the cable. Keep the cable away from hot and rotating parts. 3. Place all exces-s c-able in convolut~d tubinfJ 4. Wire tie the cable securely. Page 2 of 14 AOS.33 Operations Manual MAINTENANCE: Remove dust and dirt with 'd damp ~oft cloth. Heav;er dirt should be removed with a damp soft cloth and mild deteT9~f)t. Do not use strong cleaning agents containing gasoline, thinner. benzene or alcohol. These substances may damage the exterior surface of the monitor. **CAUTION** , Before drining, be sure no cable or wiring is on the other side. Be sure to dril1 a '6mm l'518l diame\er'110)e on)y 2 Feed as much cable as possible into vehicle and clamp secur~ly. This reduces the possibility of bein...