|
Anleitung Zusammenfassung
• Do not use a new battery together with an old one. • Do not use different types of batteries together. • Some buttons may not work with certain Sony TVs. *1 SLV-SE830B only *2 not available on SLV-SE230B Controlling other TVs with the remote commander (SLVSE830B only) The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number. 1 Set [TV] / [MAGN] at the top of the remote commander to [TV]. 2 Hold down ?/1, and enter your TV’s code number using the programme number buttons. Then release ?/1. Now you can use the following TV control buttons to control your TV: ?/1, t TV/MAGN, programme number buttons, - (ten’s digit), CHAINE +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons, (wide)*, MENU*, M/m/,*, and OK*. * These buttons may not work with all TVs. Setting up the remote commander Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. To switch to wide mode, see the footnotes below this table for the applicable code numbers. Manufacturer Code number Sony 01*1, 02 Akai 68 Ferguson 52 Grundig 10*1, 11*1 Hitachi 24 JVC 33 Loewe 45 Mivar 09, 70 NEC 66 Nokia 15, 16, 69*3 Manufacturer Code number Panasonic 17*1, 49 Philips 06*1, 07*1, 08*1 Saba 12, 13 Samsung 22, 23 Sanyo 25 Sharp 29 Telefunken 36 Thomson 43*2 Toshiba 38 *1 Press (wide) to switch the wide picture mode on or off. *2 Press (wide), then press 2 +/– to select the wide picture mode you want. *3 Press (wide). The menu appears on the TV screen. Then, press M/m/, to select the wide picture you want and press OK. Tip • When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically. Notes • If you enter a new code number, the code number previously entered will be erased. • If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander. • When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries. Getting Setting up the remote commander 15 Step 3 : Connecting the VCR Mains lead LIGNE-1 (EURO AV) ANTENNE ENTREE PERITEL to mains Aerial cable (supplied) : Signal flow PERITEL cable (supplied) Disconnect the aerial cable from 1 your TV and connect it to on the rear panel of the VCR. 2 Connect of the VCR and the aerial input of your TV using the supplied aerial cable. 3 Connect LIGNE-1 (EURO AV) on the VCR and the PERITEL connector on the TV with the supplied PERITEL cable. Whenever you want to watch the VCR picture, press t TV/MAGN to display the MAGN*1 or VIDEO*2 indicator in the display window. 4 Connect the mains lead to the mains. *1 SLV-SE830B and SE730B only *2 SLV-SE630B and SE230B only Connecting the VCR About the SMARTLINK features (not available on SLV-SE630B and SE230B) If the connected TV complies with SMARTLINK, MEGALOGIC*1, EASYLINK*2, Q-Link*3, EURO VIEW LINK*4, or T-V LINK*5, this VCR automatically runs the SMARTLINK function after you complete the steps on the previous page (the indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features. • TV Direct Rec You can easily record what you are watching on the TV when the VCR is turned on. For details, see “Recording what you are watching on the TV (TV Direct Rec) (not available on SLV-SE630B and SE230B)” on page 41. • One Touch Play With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play) (not available on SLV-SE630B and SE230B)” on page 37. • One Touch Menu When the VCR is turned on, you can turn on the TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander. • One Touch Timer When the VCR is turned on, you can turn on the TV, set the TV to the video channel, and display the timer recording menu (the MINUTERIE menu or the SHOWVIEW menu) automatically by pressing MINUTERIE on the remote commander. You can set which timer recording menu is displayed using OPTIONS PROG. in the FONCTIONS AVANCEES menu (see page 67). • NexTView Download You can easily set the timer by using the NexTView Download function on your TV. Please refer to your TV’s instruction manual. *1 “MEGALOGIC” is a registered trademark of Grundig Corporation. *2 “EASYLINK” is a trademark of Philips Corporation. *3 “Q-Link” is a trademark of Panasonic Corporation. *4 “EURO VIEW LINK” is a trademark of Toshiba Corporation. *5 “T-V LINK” is a trademark of JVC Corporation. Note • Not all TVs respond to the functions above. Getting continued Connecting the VCR 17 Additional connections To a stereo system (not available on SLV-SE630B and SE230B) You can improve sound quality by connecting a st...
Dieses Handbuch ist für folgende Modelle:Tragbare Kassettenspieler - SLV-SE730B (947.98 kb)
Tragbare Kassettenspieler - SLV-SE830B (947.98 kb)