Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
SET CLOCK ...... AUTO SET SELECT SET ENO ROTATE WHEEL PUSH WHEEL PUSH MENU KEY - yty-- SET CLOCK ЗШЗШЗПЙ Push the MENU button twice to start the clock and exit this mode. BY ROTATING WHEEL : PUSH WHEEL-* TO END PUSH MENU KEY H reí rol ROTATE WHEEL PUSH WHEEL --- SET UP CHANNEL --- ANTENNA SYSTEM : CATV SELECT SET END ROTATE WHEEL PUSH WHEEL PUSH MENU KEY To Add or Delete a Channel 1 Push the CH UP/DOWN button or the NUMBERED keys to select a channel to add or delete. The NUMBERED kevs select all channels regardless of whether they have a signal or not. The CH UP/DOWN button selects only those channels which are in the Combination VCR’s channel memory. 2 Push the ADD/DLT button to add or delete the channel. • To select a deleted channel, use the NUMBERED keys. CHANNEL 08 DELETED Ior ADDED • This Combination VCR will accurately maintain its calendar up to Dec. 31, 2089, 11:59PM. • Normal TV or Cable channels are automatically selected and placed in memory depending on how your Combination VCR is hooked up. 7 Getting Started On Screen Displays (OSD) Channel & Function Display Whenever the channel is changed, the Channel number will appear for a few seconds on-screen. (Some station names may also appear.) When a function button is pushed (PLAY, FF, etc.) the Combination VCR mode will be displayed. • When a recording is started, both REC and the channel will appear together. Menu Screen 1 Push the MENU button to display the menu. 2 Rotate and push the wheel to make your selection (see page 6). 08 m и [<>i ven рта ЙЁ ES Up CH CLOCK EXIT SELECT SET ROTATE WHEEL PUSH WHEEL Warning and Instruction Displays These displays will alert you to a missed operation or provide further instructions. WNET If no active channels NO CH FOUND are found for CHANNEL PLEASE CHECK ANTENNA MEMORY... CABLE CONNECTION THEN '— PUSH CH UP KEY AGAIN ---j If a Timer Program was not completed before exiting the Program mode... PROGRAM IS INCOMPLETE If you push the REC button on the remote control or the REC and PLAY buttons on the Combination VCR, and a cassette is inserted with no record tab... CHECK CASSETTE RECORD TAB • To get the most from each feature, it is recommended that you read the Operation Manual before attempting any operation. VCR Status & Clock Display If you push the STOP button during a Timer Recording... TO CANCEL TIMER REC HOLD DOWN STOP KEY FOfl APPROX 3 SEC Push the DISPLAY button to display and remove the overlay shown below. Rec Time Remaining (OTR mode only see page 15.) Tape Counter Function Status L Time REC 1 2 : 00AM WNET ■ -0:25 0:00:00 SLP Channel & Call Letter Tape Speed If you push the PLAY, FF, REW, or REC button on the remote control or if you push the REC and PLAY buttons, the FF, PLAY, or REW button on the Combination VCR without a cassette inserted... If you attempt to set or review a Timer Recording or set the On Timer and the Clock is not set... MO CASSETTE PLEASE INSERT A CASSETTE PLEASE SET CLOCK BEFORE PROGRAMMING Blank Tape and will be Blue Screen If a blank section of tape is encountered in the Play mode or the channel you select has no broadcast, the TV screen will change to a solid blue field. The screen will remain blue until a recorded signal is again detected or an active channel is selected. Two minutes before a Timer Recording is about to begin... PLEASE PREPARE FOR TIMER REC 8 TV Operation IViCheck list before you begin □ All connections are made. (See page 5.) □ Your Combination VCR is plugged in. MUTE RAPID TUNE о Push POWER to turn the Combination VCR on. Select a channel using CHANNEL UP/DOWN or NUMBERED keys. Push VOLUME UP/ DOWN to adjust the volume level. Using the 100 key When selecting CATV channels 100 to 125 with the NUMBERED keys, first push the 100 key and then enter the remaining two digits. For example, for channel 125: Push the NUMBERED keys 100-2-5. Rapid Tune Push the R-TUNE button to display the last channel you were watching. Previous channel CH08 Preset Channel CH10 When selecting channels with the CH UP/DOWN button, the channels must be displayed for at least 4 seconds in order for the Combination VCR to recognize them as a new selection. Audio Mute Push the MUTE button to instantly mute the sound. Push again, to restore the previous sound level. Phones Connect an earphone (not supplied) or headphone (not supplied) to the Phones Jack. FCC WARNING: Any unauthorized changes or modifications to this equipment would void the user’s authority to operate. Note to CATV System Installer This reminder is provided to call the CATV (Cable TV) System Installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 9 Basic TV Operation fl Picture Adjustment sf, ...