Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Anleitung Zusammenfassung
When the tape reaches the position specified by DATA, the insert operation will end, and the VTR will go into the PLAY PAUSE mode. This operation can be canceled by an OSP command. If the operation mode changes as a result of a key input from the VTR proper or the remote controller, the insert operation will be canceled. When a command other than OSP, QCD, QOP, QOS, RCK, QRV or QID is sent by an EIT command during an insert operation, a command error will be returned from the VTR. [STXJEIT: □□□ □□□□□ [ETX] [STX]EIT[ETX] Counter data □ □ □□ □□ □□ Sign Hours Minutes Seconds Frames -: Minus sign +: Blank Example: When an insert operation is performed up to 1 hour, 12 minutes, 35 seconds and 00 frames [STX]EIT:^_1123500[ETX] Be sure to insert a blank. EAT: DATA This command specifies a post-recording up to the specified position. If this command is input when the VTR is in the PLAY PAUSE, SLOW PAUSE or AUDIO DUB PAUSE mode, a post-recording operation will take place to the specified position. When the tape reaches the position specified by DATA, the post-recording operation will end, and the VTR will go into the PLAY PAUSE mode. This operation can be canceled by an OSP command. If the operation mode changes as a result of a key input from the VTR proper or the remote controller, the post-recording operation will be canceled. When a command other than OSP, QCD, QOP, QOS, RCK, QRV or QID is sent by an EIT command during an insert operation, a command error will be returned from the VTR. [STX]EAT: □□□ □□□□□ [ETX] [STX]EAT[ETX] Counter data □ □ □□ □□ □□ Sign Hours Minutes Seconds Frames Minus sign +: Blank Example: When an audio insert operation is performed up to 1 hour, 12 minutes, 35 seconds and 00 frames [STX]EAT:_^_1123500[ETX] Be sure to insert a blank. 20 Send command Description of operation Personal computer send data Reply data sent back from VTR EVT: DATA This command specifies an AUDIO & VIDEO INSERT up to the specified position. If it is sent when the VTR is in the AUDIO DUB PAUSE or AUDIO & VIDEO INSERT PAUSE mode, an AUDIO & VIDEO INSERT operation will take place up to the specified position. When the tape reaches the position specified by DATA, the AUDIO & VIDEO INSERT operation will end, and the VTR will go into the PLAY PAUSE mode. This operation can be canceled by an OSP command. If the operation mode changes as a result of a key input from the VTR proper or the remote controller, the AUDIO & VIDEO INSERT operation will be canceled. When a command other than OSP, QCD, OOP, QOS, RCK, ORV or QID is sent during EVT in AUDIO & VIDEO INSERT operation, a command error will be returned from the VTR. [STXJEVT: (“inn □□□□□ [ETX] [STX]EVT[ETX] Counter data □ □ □□ □□ □□ Sign Hours Minutes Seconds Frames -: Minus sign +: Blank Example: When an audio insert operation is performed up to 1 hour, 12 minutes, 35 seconds and 00 frames [STXJEVT:_1123500[ETX] t Be sure to insert a blank. EVT SMC SMF Precaution: • If the VTR proper goes into the Memory Stop mode during an insert operation (EIN, EVT, EIT), it will cut off when the counter reading becomes “0:00.00.00". Be sure, therefore, to cancel the Memory Stop mode in advance. An insert operation will also be interrupted when a VTR key, remote controller key, Memory/Search button or Reset button is operated, so do not operate these keys or buttons during an insert operation. ■ SEARCH COMMAND Send command Description of operation Personal computer send data Reply data sent back from VTR SMC (SEARCH MODE COARSE) This command sets the mode in which a search is performed by the SCP or SCS command to the High Speed Search mode. The search time can be reduced by performing a search in the FF or REW mode, however in this case the search accuracy falls off. If high search accuracy is required, use the following SMF command. If this command is sent, the VTR will be maintained in the COARSE mode until SMF is sent. [STX]SMC[ETX] [STX]SMC[ETX] SMF (SEARCH MODE FINE) This command sets the mode in which a search is performed by the SCP or SCS command to the Precision Search mode. The shuttle search speed is controlled according to the distance to the target, and the search accuracy is ±1 frame. If this command is sent once, the VTR will go into the FINE mode and remain in that mode until SMC is sent. Precaution: In this mode, a search is performed by CUE or REVIEW, hence a search cannot be performed for more than 10 minutes (more than 70 minutes on the tape). Processing is interrupted mid-way in order to protect the tape. [STX]SMF[ETX] [STX]SMF[ETX] 21 SCP scs SPT Send command Description of operation Personal computer send data „ Reply data sent back from VTR SCP: DATA This command searches for the position specified by DATA, then puts the VTR into the PLAY mode at the end of the search. The search takes place in the mode specified by the SMC or SMF command. It is accepted if the VTR is in the STOP, PLAY, REW, FF, PLAY PAUSE, REVERSE PLAY, SLOW PA...