Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Playback 1 Turn on the camcorder and the connected TV or VCR. On the TV: Select as the video input the same terminal to which you connected the camcorder. On the VCR: Set the input selector to the external video input (usually labeled LINE IN). 2 Start the playback of the movies ( 27) or still images ( 31). NOTES • ..Turn off all the devices before starting the connections. • ..Sound from the built-in speaker will be muted while the STV-250N Stereo Video Cable is connected to the camcorder. • ..We recommend powering the camcorder using the compact power adapter. • ..If you connect to a TV using the HDMI connection –connection type 3 – or the video component connection –connection type 1 – you can enjoy the full resolution of high-definition TV. • ..About the HDMI terminal The HDMI (High-Definition Multimedia Interface) connection –connection type 3 – is a convenient all-digital connection using a single cable for both video and audio. When you connect the camcorder to an HDTV equipped with an HDMI terminal, you can enjoy video and audio playback at the highest quality. -The HDMI terminal on the camcorder is for output only. Do not connect it to an HDMI output terminal on an external device, as this may damage the camcorder. -The HDMI connection will recognize automatically the highest resolution supported by the connected HDTV, and output the optimal video signal to ensure the best viewing experience. You can confirm the current specification of the video output in the [HDMI OUT] information display at the bottom of the PLAY/OUT SETUP2 menu screen in mode ( PLAY/OUT SETUP menu in other modes). -Correct operation cannot be guaranteed when connecting the camcorder to DVI monitors. -Some HDTVs have their HDCP digital content protection configured so as not to allow the playback of personal content (video recorded for personal uses). If you cannot play back the video recorded with this camcorder on your HDTV using the HDMI connection, try connecting the camcorder using the video component connection –connection type 1 – instead. -There will be no video output from the AV/ terminal or the COMPONENT OUT terminal while the camcorder is connected to an external device using the HDMI cable. In such case, only audio will be output from the AV/ terminal. External Connections 68 68 Connecting to a TV or VCR -There will be no video or audio output from the HDMI OUT terminal while there is a video input connection to the HDV/DV terminal or the AV/ terminal. -To output audio dubbed later on a tape through the HDMI OUT terminal, set [AUDIO OUT] to [ MIX/VAR.] ( 39). -Audio output from the HDMI OUT terminal will include both channels (Left/Right on a stereo recording, Main/Sub on a bilingual recording), regardless of the [OUTPUT CH] setting. Recording to a VCR or Digital Video Recorder You can copy your recordings by connecting the camcorder to a VCR or a digital video device. When recording to a digital video recorder using the HDV/DV terminal, you can copy recordings with virtually no generation loss in video and sound quality. Connect the camcorder to the external device following one of the connection diagrams shown in the previous section Connection Diagrams ( 64). POINTS TO CHECK ( 8) Change the following settings as necessary before making the connections. Refer to the corresponding explanation of each setting in the PLAY/OUT SETUPmenu option list ( 38). -[PLAYBACK STD] to select the output video standard. -[DV OUTPUT] to select the standard of the output video when using connection type 2 . Note that the video standard of the recorded copy depends also on the standards supported by the external digital device. Refer to the table below. -Set [AV/PHONES] to [ AV] when using connection type 4 or 5 . Connecting Connect the camcorder to a VCR or other analog device using connection types or 4 5 , or to a DVD recorder or other digital recording device using connection type 2 , as shown in the previous section Connection Diagrams( 64). Settings for Recording Video Output using the HDV/DV Terminal Video Output Signal Standard of the Recording on the Tape Standard Supported by the External Digital Device* [PLAYBACK STD] Setting [DV OUTPUT] Setting High Definition HDV HDV [ AUTO] or [ HDV] [ HDV/DV] Standard HDV DV [ AUTO] or [ HDV] [ DV LOCKED] Definition DV DV [ AUTO] or [ DV] [ [ HDV/DV] or DV LOCKED] * To output video in high definition verify that the DV terminal on the external digital device is compatible with the MPEG2-TS protocol; to output video in standard definition, verify that it is compatible with the DV standard. 69 Recording 1 This camcorder: Load the recorded cassette. 2 Connected device: Load a blank cassette or disc and set the device to record pause mode. 3 This camcorder: Locate the scene you wish to copy and pause the playback shortly before the scene. When the connection is recognized " HDV/DV" will be displayed. When the video output starts, the display will change to " HDV-OUT" or " DV-OUT" depending...