Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Fotos und technische Daten Canon MV700 |
Anleitung Zusammenfassung
The wide attachment is for use at maximum wide-angle. Screw the wide attachment fully into the lens filter thread. Basic Preparations . Do not look directly at the sun or other strong light sources through the wide attachment. It could damage your eyesight. . If you zoom to telephoto, the picture will not be in focus. . The wide attachment may obstruct the remote sensor (the range of the wireless controller narrows), or may cause a shadow to appear on the picture when recording with a video light or the assist lamp (White LED). . Filters cannot be used with the wide attachment. . If dust accumulates on the wide attachment or on the camcorder lens, clean both lenses gently with a blower brush. . Do not touch the lens to avoid smudges and fingerprints. . Do not store the wide attachment in a humid place as it may mold. 17 Using the Wireless Controller Point it at the camcorder’s remote sensor when you press the buttons. Inserting Batteries The wireless controller operates with two AA (R6) batteries. 1. Open the battery cover. 2. Insert the batteries following the + and – markings. Replace both batteries. 3. Close the battery cover. . Camcorder and wireless controller are equipped with 2 remote sensor modes ( 46). If the wireless controller does not work, check if camcorder and wireless controller are set to the same mode. . The wireless controller may not work properly when the remote sensor is subjected to strong light sources or direct sunlight. Setting the Time Zone, Date and Time E Set the time zone, date and time when you first start using your camcorder, or when you have replaced the backup battery. Setting the Time Zone/Daylight Saving Time PLAY (VCR) CAMERA CARD PLAY CARD CAMERA SYSTEM T.ZONE/DST•••PARIS ( 38) 1. Press the MENU button to open the menu. 2. Turn the SET dial to select [SYSTEM] and press the SET dial. 3. Turn the SET dial to select [T.ZONE/DST] and press the SET dial. Basic Preparations The time zone setting appears (see table on the next page). The default setting is Paris. 4. Turn the SET dial to select the setting option that represents your time zone and press the SET dial. To adjust for daylight saving time, select the time zone with the U next to the area. Setting the Date and Time PLAY (VCR) CAMERA CARD PLAY CARD CAMERA D/TIME SET••• 1.JAN.2004 SYSTEM 12:00 PM ( 38) 5. Turn the SET dial to select [D/TIME SET] and press the SET dial. The year display starts to flash. 6. Turn the SET dial to select the year, and press the SET dial. • The next part of the display starts flashing. • Set the month, day, hours and minutes in the same way. 19 7. Press the MENU button to close the menu and to start the clock. 1 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 2 3 5 6 7 9 8 10 4 12 11 13 24 19 20 18 17 21 23 22 15 14 16 Time zone LONDON PARIS CAIRO MOSCOW DUBAI KARACHI DACCA BANGKOK H. KONG (Hong Kong) TOKYO SYDNEY SOLOMON WELLGTN (Wellington) SAMOA HONOLU. (Honolulu) ANCHOR. (Anchorage) L.A. (Los Angeles) DENVER CHICAGO N.Y. (New York) CARACAS RIO (Rio de Janeiro) FERNAN. (Fernando de Noronha) AZORES No. Time zoneNo. Once you have set time zone, date and time, you do not need to reset the clock each time you travel to another time zone. Just set the time zone to the one of your destination, and the camcorder automatically adjusts the clock. Displaying Date and Time during Recording You can display the date and time in the lower left corner of the screen. PLAY (VCR) CAMERA CARD PLAY CARD CAMERA E DISPLAY SETUP/ D/T DISPLAY••OFF ( 38) 1. Press the MENU button to open the menu. 2. Turn the SET dial to select [DISPLAY SETUP/ ] and press the SET dial. 3. Turn the SET dial to select [D/T DISPLAY] and press the SET dial. 4. Turn the SET dial to select [ON]. 5. Press the MENU button to close the menu. Basic Preparations 21 Recording Movies on a Tape Before You Begin Recording Make a test recording first to check if the camcorder operates correctly. Before you make important recordings, clean the video heads ( 135). Recording 1. Remove the lens cap. 2. Set the camcorder to CAMERA mode. • Set the POWER switch to CAMERA and the TAPE/CARD switch to b. • Set the POWER switch to CAMERA. 3. Push the OPEN button at the LCD panel and open the LCD panel. 4. Press the start/stop button to begin recording. Press the start/stop button again to pause recording. When You Have Finished Recording r e ( VCR ) POWER CAMERACAMERA PLAY OFF q w ( V C R ) POWERPOWER CAMERACAMERA PLAYPLAY OFFOFF 1. Turn the POWER switch to OFF. 2. Close the LCD panel and return the viewfinder into its initial position. 3. Replace the lens cap. 4. Unload the cassette. 5. Disconnect the power source. . Wait until the tape counter stops completely before you start recording. . When you do not remove the cassette, you can record the next scene without E producing any noise or blank sections between the recordings even if you turn the camcorder off. . Bright light may make it difficult to use the LCD screen. In such case, use t...