Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Fotos und technische Daten Canon MVX200i |
Anleitung Zusammenfassung
. Use only tapes recorded in SP mode 12-bit audio sound with this camcorder. Audio dubbing will stop if the tape has a blank section or a section recorded in LP mode or 16-bit mode. . You cannot use the DV terminal for audio dubbing. . If you add sound to a tape not recorded with this camcorder, sound quality may decrease. . Sound quality may decrease when you add sound to the same scene for more than 3 times. . When you connect an audio device, check the picture on the LCD screen and the sound via built-in speaker or audio device. You can also connect a TV via S-video terminal. . When you use the built-in microphone, you can either connect a TV via AV terminal to check the picture, or headphones to check the sound. When you connect a TV via S-video terminal, you can check the picture on the TV screen and the sound with headphones connected to the camcorder. . Set the zero set memory at the end of the scene you wish to dub audio. The camcorder will automatically stop audio dubbing at that point. 89 Playing Back the Added Sound You can select to play back Stereo 1 (original sound), Stereo 2 (added sound), or adjust the balance of both sounds. PLAY (VCR) CAMERA CARD PLAY CARD CAMERA AUDIO SETUP 12bit AUDIO•••STEREO1 ( 37) 1. Open the menu and select [AUDIO SETUP]. Select [12bit AUDIO], select a setting and close the menu. • STEREO 1: Plays back the original sound. • STEREO 2: Plays back the added sound. • MIX/FIXED: Plays back Stereo 1 and Stereo 2 in the same level. • MIX/VARI.: Plays back Stereo 1 and Stereo 2. The mix balance can be adjusted. 2. If you have selected [MIX/VARI.], adjust the mix level: Open the menu and select [AUDIO SETUP]. Select [MIX BALANCE], adjust the balance with the SET dial and close the menu. Turn the SET dial down to increase the volume of Stereo 1 and up to increase the volume of Stereo 2. . The camcorder resets to [STEREO1] when you turn the camcorder off. However, the mix balance is memorised by the camcorder. . You can also press the 12bit AUDIO OUT button on the wireless controller to select the audio output. However, the mix balance can only be adjusted in the menu. Connecting to a Computer Using a DV (IEEE1394) Cable E You can transfer recordings to a computer equipped with a IEEE1394 (DV) terminal or IEEE1394 capture board. Optional software is required for transferring recordings from the tape to a computer. Refer to the instruction manual of the software. Use the optional CV-150F (4 pin–4 pin) or CV-250F (4 pin–6 pin) DV Cable. IEEE1394 (DV) terminal DV Cable (optional) 6-pin 4-pin . Operation may not work correctly depending on the software and the specifications/settings of your computer. . If the computer freezes while you have connected the camcorder, disconnect and reconnect the DV cable. If the problem persists, disconnect the interface cable, turn off camcorder and computer, turn camcorder and computer back on and reconnect them. . Do not disconnect the DV cable, open the memory card cover, remove the memory card, change the position of the POWER switch or turn off the camcorder and computer while data is being transferred to the computer (while the camcorder’s card access indicator is flashing). Doing so may damage the memory card’s data. . The image files on your memory card and the image files saved on the hard disk drive of your computer are valuable, original data files. If you wish to use image files on your computer, make copies of them first, and use the copied file, retaining the original. . We recommend powering the camcorder from a household power source while it is connected to the computer. . Refer also to the instruction manual of the computer. . Users of Windows XP can use the supplied DV Network Software. For details, refer to the DV Network Software Instruction Manual. Editing 91 Inserting and Removing a Memory Card You can use SD Memory Cards or commercially available MultiMediaCards with this camcorder. The SD Memory Card has a protect switch to prevent accidental erasure. Terminals Inserting the Card 1. Turn off the camcorder. 2. Open the cover. 3. Insert the memory card all the way into the memory card slot. 4. Close the cover. Do not close the cover forcefully without having the card correctly inserted. Removing the Card Do not forcefully remove the memory card without first pushing it in. 1. Turn off the camcorder. Make sure that the card access indicator is not flashing before you turn off the camcorder. 2. Open the cover. 3. Push the memory card to release it. Remove the memory card. 4. Close the cover. Card access indicator . This camcorder is compatible with SD Memory Cards or MultiMediaCards only. Do not use any other types of memory cards. . Turn off the camcorder before inserting or removing the memory card. Otherwise, it may result in data damage. . If you use memory cards other than the supplied one, make sure to format them with the camcorder ( 117). Selecting the Image Quality/Size E Changing the Still Image Quality You can choose...
Dieses Handbuch ist für folgende Modelle:Kameras - MVX250i (8.19 mb)