Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
The actual number of frames per second will be lower when the shutter speed is 1/30 or slower. Photos CONTINUOUS SHOOTING/ HIGH-SPEED CONTINUOUS SHOOTING 1 Press PHOTO halfway to activate the autofocus. 2 Press PHOTO fully and hold it pressed down. A series of still images will be recorded as long as you hold the button pressed. AUTO EXPOSURE BRACKETING Press PHOTO , first halfway to activate the autofocus and then fully to record the still images. Three still images in different exposures will be recorded. Histogram Display When viewing still images you can display the histogram and the icons of all the functions used at the time of recording. Use the histogram as a reference to verify the correct exposure of the still image. ( 24) The area to the right of the histogram represents highlights and the left side represents shadows. A still image whose histogram skews to the right is relatively bright; while one whose histogram peaks to the left, is relatively dark. Pixel Count Shadows Highlights NOTES The histogram will appear also after recording a still image, while reviewing it within the time set for the [REVIEW] option (or immediately after recording it, if [REVIEW] is set to [ OFF]). You can choose to turn off the histogram by pressing DISP. ( 49). Protecting Photos You can protect still images from accidental erasure. ( 24) 1 Open the image selection screen. FUNC. [ PROTECT] [ PROTECT] appears on the screen. 2 Select ( ) the still image you want to protect. 3 Press to protect the still image. appears on the bottom bar and the image cannot be erased. Press again to cancel the image protection. 4 Repeat steps 2-3 to protect additional images or press twice to close the menu. IMPORTANT FUNC. Initializing the memory ( 30) will permanently erase all recordings, including protected still images. / Copying Photos You can copy still images from the built- in memory to the memory card and vice versa. ( 24) POINTS TO CHECK Select in advance the memory from which you want to copy the still images ( 57). Copying a Single Image FUNC. [ COPY] [YES] FUNC. Copying Images from the Index Screen Options [ALL IMAGES] Copies all the still images. [ONE IMAGE] Copies only the selected still image. 1 Move the zoom lever toward W. The still image index screen appears. 2 Select the memory from which you want to copy the still images. Refer to To select which still images to play back ( 57). 3 If you want to copy only one image, select ( , ) the still image you want to copy. 4 Copy the still image(s). FUNC. [ COPY] Desired option [YES]* [OK]** FUNC. * When copying all the still images, press twice to interrupt the operation while it is in progress. **When copying a single still image, this step is not necessary. IMPORTANT Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. -Do not open the memory card slot cover. -Do not disconnect the power source or turn off the camcorder. -Do not change the position of the mode dial. Photos NOTES • If there is not enough space on the destination memory, the camcorder will copy as many still images as possible before stopping the operation. • If the memory card slot cover is open, or the LOCK switch on the memory card is set to prevent writing, you will not be able to copy still images to the memory card. You can also use the following functions... The following functions and features of the camcorder can be used either for shooting video or for taking photos. The way to set and use them was already explained in detail, so we refer you to the relevant page in the “Video” section. • Zoom ( 33) • Quick Start ( 35) • Recording programs ( 42, 43) • Mini video light ( 44) • Self timer ( 45) • Automatic backlight correction and manual exposure adjustment ( 45) • Manual focus adjustment ( 46) • White balance ( 47) • Image effects ( 48) • Digital effects ( 48) Printing Photos Printing Photos The camcorder can be connected to any PictBridge-compatible printer. You can mark in advance the still images you want to print and set the desired number of copies as a print order ( 65). Canon printers: SELPHY printers of the CP, DS and ES series and PIXMA printers marked with the PictBridge logo. ( 24) Connecting the Camcorder to the Printer 1 Insert the memory card containing the still images you want to print. / Select in advance the memory from which you want to print the still images ( 57). 2 Turn on the printer. 3 Connect the camcorder to the printer using the supplied USB cable. • Connection . Refer to Connection Diagrams ( 67). • If the device type selection screen appears, select [PC/PRINTER] and press . • If the still image index screen is displayed, move the zoom lever toward T to display a single image. • appears and changes to . • The (print/share) button lights up and the current print settings will be displayed for approx. 6 seconds. IMPORTANT • If continues to flash (for more than 1 minute) or if does not appear, the ...
Dieses Handbuch ist für folgende Modelle:Kameras - FS100 (3.44 mb)
Kameras - FS11 (3.44 mb)