Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Repeat the same procedure to set the date and year. . When you set the time, press and hold rt to change the time by 30 minutes. . When you set the date, press and hold rt to change the date by 15 days. F F Set Just Clock. The default setting is “OFF”. Set as desired by pressing rt, then press OK or e. . For the Just clock function, refer to “Just Clock” on page 80. . If you set to “OFF”, you can disregard the next step as you won’t be able to receive regular clock adjustments. G G Set the source channel position for clock data. The recorder is preset to receive clock setting and adjustment data from channel position 1. Press rt to set the channel position to the number representing the station transmitting clock setting data, then press OK or e. H H Start the clock operation. Press MENU. NOTES: . Just Clock (when set to “ON”) adjusts the recorder’s built-in clock every hour, except for 23:00, 0:00, 1:00 and 2:00. . Just Clock is not effective when ... ... the recorder’s power is on. ... the recorder is in the Timer mode. ... a difference of more than 3 minutes exists between the built-in clock’s time and the actual time. ... the recorder is in the Power Save mode (. pg. 67). ... “L-2 SELECT” is set to “SAT” (. pg. 53). . If Just Clock is set to “ON”, the recorder’s clock is automatically adjusted at the start/end of Summer Time. . Just Clock may not function properly depending on the reception condition. SUBSIDIARY SETTINGS (cont.) VIDEO Plus+® System Setup IMPORTANT Normally, Auto Set Up (. pg. 13), Preset Download (. pg. 14) or Auto Channel Set (. pg. 72) sets the Guide Program numbers automatically. You need to set the Guide Program numbers manually only in the following cases. . When timer-programming with the VIDEO Plus+ system, the channel position, where the station you wish to record is received on your recorder, is not selected, OR when you add a channel after Auto Set Up, Preset Download or Auto Channel Set has taken place, —Set the Guide Program number for that station manually. . When you wish to timer-record a satellite programme with the VIDEO Plus+ system, —Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver. Turn on the TV and select the AV mode. Guide Program Number Set A A Access the Main Menu screen. Press MENU. B B Access the Initial Set screen. Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or e. C C Access the Guide Program Set screen. Press rt to move the highlight bar (pointer) to “GUIDE PROG SET”, then press OK or e. D D Enter the Guide Program number. Press rt to enter the Guide Program number for the desired station as shown in the TV listings. Then press OK or e. (Example)When inputting the Guide Program number 4 for CH4. E E Enter the receiving channel position number. Press the number key “0” to select “TV PROG” or “SAT”. Then press rt to input the number of the recorder’s channel position on which the Guide Program number’s broadcast is received by the recorder or the satellite receiver. Then press OK or e. . To timer-record a satellite programme with the VIDEO Plus+ system, you need to install the provided Satellite Controller and perform the procedure described in “Satellite Receiver Control Setting” (. pg. 17). . Repeat steps 4 and 5 as necessary. (Example) If CH4 is received on channel position 4. F F Return to the normal screen. Press MENU. Guide Program Number “Guide Program (GUIDE PROG) number” refers to the assigned TV station numbers, according to broadcast area, for the VIDEO Plus+ timer recording. The Guide Program numbers can be found in most TV listings. TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. No power is supplied to the recorder. . The mains power cord is disconnected. Connect the mains power cord. 2. The clock is functioning properly, but the recorder cannot be powered. . “#” is displayed on the front display panel with “AUTO TIMER” set to “OFF”. Press the # button to turn the “#” indicator off. 3. The remote control won’t function. . The batteries are discharged. Replace the dead batteries with new ones. TAPE TRANSPORT SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The tape does not run during recording. . “i” is displayed on the front display panel. Press 4 to turn the “i” indicator off. 2. The tape will not rewind or fast- forward. . The tape is already fully rewound or fast-forwarded. Check the cassette. PLAYBACK SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The playback picture does not appear while the tape is running. . The TV receiver is not set to the AV mode. Set the TV to its AV mode. 2. Noise appears during visual search. . This is normal. 3. Noise appears during normal playback. (VHS deck only) . The automatic tracking mode is engag...