Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Panasonic Dateigröße: 1.15 mb Dateiname: AKHC931P.PDF Unterrichtssprache:

The images to be output are selected using the monitor output selector switch. k Rear VF connector This D-sub connector is used for Viewfinder interface. 10 2 Align the center mark on the lens with the groove at the top center of the lens mount, and mount the lens. 3 Lower the lens clamp lever to clamp the lens in place. 4 Insert the cable into the cable clamp and connect it to the LENS connector. . For details on handling the lens, refer to the instructions that accompany the lens. . Depending on the lens mounted, it may be necessary to perform the following lens and camera adjustments. 1. Flange back adjustment for the lens 2. Auto iris operation speed adjustment for the lens 3. White shading adjustment for the lens (performed using the controls on the camera) 1 Raise the lens clamp lever, and remove the mount cap. Mounting the lens Mount cap Lens clamp lever Center mark LENS connector Adjusting the lens flange back Adjust the flange back (distance from the surface where the lens is mounted to the surface where the images are formed) if the subject fails to be precisely focused at both the telephoto and wide-angle settings when zoom operations are to be performed. Once adjusted, the flange back does not need to be adjusted again unless the lens is replaced. Adjustment method For details on the adjustment method and positions of the lens parts, refer also to the instructions that accompany the lens. About 10 ft (3 m) 1 Mount the lens on the camera. Do not forget to connect the lens cable at this time. 2 Set the lens iris to manual, and open the iris. 3 Set the lighting in such a way that the appropriate video output level is obtained at a distance of about 10 ft (3 meters) from the flange back adjustment chart. If the video level is too high, use a filter or shutter. 4 Loosen the screw that secures the F.f (flange focus) ring. Depending on the lens concerned, this ring may be marked as the “F.b” (flange back) ring. 5 Set the zoom ring to the telephoto position either by manual or electrical means. 6 Shoot the flange back adjustment chart, and turn the distance ring to adjust the focus. 7 Set the zoom ring to the wide-angle position, and turn the F.f ring to adjust the focus. Take care not to move the distance ring. 8 Repeat steps 5 to 7 until the chart is focused properly at both the telephoto and wide-angle positions. 9 Tighten up the screw that secures the F.f ring. 12 Performing the viewfinder adjustments (The viewfinder is an optional accessory.) Attaching the viewfinder Stopper screw Stopper screw 1 Check that the camera’s POWER switch is at the OFF position. 2 Attach the accessory mounting plate to the viewfinder. 5 Connect the plug to the viewfinder’s connector. When connecting the plug to the viewfinder’s connector, ensure that it is fully and securely inserted. 3 Pull up the knob on the mounting plate and slide the plate to attach the viewfinder. 4 Tighten the stopper screw securely. Detaching the viewfinder 1 Check that the camera’s POWER switch is at the OFF position. 2 Loosen the stopper screw, pull up the knob on the mounting plate and slide the viewfinder along and off the plate. 3 Disconnect the plug from the viewfinder cable connector. Remove mounting plate from the viewfinder Mounting plate supplied to AK-HC931P Pull up the knob Pull up the knob Performing the viewfinder adjustments (The viewfinder is an optional accessory.) Left or right position adjustment Forwrd or backward position adjustment 1 Loosen the stopper screw. 1 Rotate the viewfinder forward/backward position fixing lever towards the outside to release the it from the locked position. Viewfinder Lever Viewfinder Stopper screw 2 Move the viewfinder to the left or right to adjust its 2 Move the viewfinder forward or backward to adjust its position. position. 3 Tighten the stopper screw. 3 Rotate the viewfinder forward/backward position fixing lever in the opposite direction until it locks. Stopper screw Connecting a microphone When the microphone is mounted on the viewfinder (optional accessory) for use The microphone of the microphone kit AJ-MC700P (optional accessory) can be mounted on the viewfinder. 1 Open the microphone holder. 4 If the audio channel whose signals are to be recorded so requires, set the AUDIO IN switch to F. INCOM1 INCOM2 BREAKER RET CONT EXT I/O POWER CCU OFF EXT SEE MANUAL TALLY OUT EARPHONE TRUNK RCB MIC1 MIC2 DC INPUSHPUSH F R PROMPER OUT GL IN AUDIO IN switch Microphone holder 2 Mount the microphone and tighten up the clamp screw. Clamp screw 3 Connect the microphone cable to the MIC IN connector on the camera. MIC IN connector 15 Mounting the camera on a tripod 1 Mount the tripod attachment on the tripod. Consider the center of gravity of the camera and tripod together when selecting the holes for attaching the camera. Check that the diameter of the selected holes match the diameter of the screws on the tripod platform. 2 Mount the camera on the tripod attachment. ...

Herunterladen

Geben Sie zwei Ziffern: