Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
When it is less than 21 minutes long, one segment will go off for every 3-minute reduction in the length. Remaining battery level When the digital display (% display) battery is used, the 7 segments light up all the way to the “F” position if the remaining battery level is more than 70%. If the remaining battery level is under 70%, one of the segments goes off for each further 10% reduction in the remaining level. CH1 CH2 20 0 EMPHASIS dB 10 30 40 E TAPE F E BATT F RF SERVO HUMID SLACK DF SLAVE TCG HOLD WIDE h min s frm . VTR Section Operation/Status-Related Displays Lights DF SLAVE TCG HOLD WIDE Error code: Indicated in the display window. Warning display RF: Lights when video head clogging occurs. SERVO: Lights when the servo is out of order. EMPHASIS 0 10 DF SLAVE TCG HOLD WIDE h min s frm E TAPE F 20 E BATT F 30 40 RF SERVO HUMID SLACK CH1 dB CH2 HUMID: Lights when condensation occurs on the head drum. SLACK: Lights when tape wind-up trouble occurs. See “Warning System” (page 149) for a detailed description. – 64 – Displays WIDE CH1 CH2 20 0 EMPHASIS dB 10 30 40 E TAPE F E BATT F RF SERVO HUMID SLACK DF SLAVE TCG HOLD h min s frm Time Code-Related Displays These lamps light to indicate the time code, CTL and real time displays. DF: This lamp lights during drop frame mode SLAVE: This lamp lights when the time code is locked to an external source. HOLD: This lamp lights when the time code generator is held (when the HOLD button is pressed). WIDE: This lamp lights when a tape is recorded or played back with an aspect ratio of 16:9. Time counter display: This displays the time code, CTL, user bit and real time. See below for the relationship between displayed items and switch settings. Relationship between the TCG and DISPLAY switch setting positions and the time counter display The item displayed in the time counter display is determined by the TCG switch and DISPLAY switch settings. Time code-related switch settings and display items TCG switch position DISPLAY switch position Displayed item SET TC or CTL Time code UB User bit CTL CTL F-RUN or R-RUN TC Time code UB User bit – 65 – Adjusting the Time and Date Adjustment and Setup Using the Setting Menu 1 Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP button are held down together. 2 Press the PAGE button to display the MAIN menu screen 3 of 4. 3 Press the SHIFT/ITEM button to move the cursor to the “TIME/DATE” position. 4 Press the UP or DOWN button to open the TIME/DATE page. .| TIME/DATE { YEAR : 99 MONTH : 01 DAY :01 HOUR : 00 MINUTE : 00 »TIME/DATE SET 5 Press the SHIFT/ITEM button to select the item to be changed. 6 Press the UP (or DOWN) button to change the setting value. The number is incremented by 1 each time the UP button is pressed and decremented by 1 each time the DOWN button is pressed. | TIME/DATE { YEAR : 99 MONTH : 01 DAY :01 HOUR : 00 .MINUTE : 00 »TIME/DATE SET 7 When the settings have been completed, press the SHIFT/ITEM button to select TIME/DATE SET and then press the UP (or DOWN) button. The time starts from when the button is pressed. »TIME/DATE SET 8 When menu operations have been completed, set the MENU SET/OFF switch to OFF. The setting menu disappears from the viewfinder screen and the displays indicating the unit’s current status appear at the top and bottom of the viewfinder screen. Note. The seconds cannot be set and always start from 0 seconds. – 66 – Adjustments and Setup During Recording Adjustments and Setup Using the Setting Menu Adjustments and setup operations during recording are performed at the setting menu. Setting menu operations are basically performed according to the procedures described on page 52. However, these procedures vary slightly according to the item. Items which can be adjusted or set up at the setting menu are as follows. Adjustment/setup items at the setting menu Adjustment/setup item Page name Operation reference Setting the gain selector value SETTING (LOW/MID/HIGH) Setting the Gain Selector Value, Setting the DTL and gamma, etc. Selecting the shutter speed/ mode to be used SHUTTER SPEED Setting the Electronic Shutter Setting the synchro scan mode shutter speed SYNCHRO SCAN Setting the Electronic Shutter Selecting the required VTR functions VTR FUNCTION Selecting Functions Shading adjustment AUTO SHADING Shading Adjustment Setup card data operations SET UP CARD Setup Card Operations –67 – Adjustments and Setup During Recording Setting the Gain Selector Value When shooting in locations without sufficient brightness, bright images can be obtained by raising the gain. However, care should be taken as raising the gain also increases the noise. The gain value for the image amplifier is selected by the GAIN switch. The gain values corresponding to the L, M and H positions of the GAIN switch are set at the MASTER GAIN page of the setting menu. Setting the gain selector value 1 Set the MENU SET/OFF switch to the SET position while the SHIFT/ITEM button and UP butto...