Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
34) ■ REW/Search (p. 34) ■ Pause/Select (pp. 16, 17, 36) ■ Stop/Set (pp. 16, 17, 32, 47) Slow/Frame Advance (Forward) (pp. 35, 36) Slow/Frame Advance (Backward) (pp. 35, 36) ■ Index Search (Forward) (pp. 36, 37) ■ Index Search (Backward) (pp. 36, 37) ■ Speaker Volume (p. 33) ■ Rec/Pause (p. 18) ■ Tele (Zoom) (p. 21) ■ Wide (Zoom) (p. 21) ■ Date/Time (p. 112) ■ Reset (p. 45) ■ PhotoShot (p. 20) ■ Display On TV (p. 39) ■ Counter/Time Code (p. 113) Audio Dubbing (p. 44) ■ Record (p. 47) ■ Menu (p. 17) Play (p. 32) 9 Note Before Use Before Using Replace the Battery 1 While pressing the tab in the direction of the arrow (A) with your fingernail, pull out the Battery Tray (B). 2 Insert the battery into the Battery Tray with the + mark facing up. Do not reverse the polarity. З Insert the Battery Tray. rReplace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may present a risk of fire or explosion. Caution: battery may explode if mistreated. Dispose of used battery properly. Keep away from children. Do not recharge, disassemble or dispose of in a fire. Remote Controlling Two Palmcorders You can control any two Panasonic Palmcorders with one Remote control. In order for the remote to distinguish between the two units, it is necessary to set one of the Palmcorders to VCR 2. On the remote, press VCR 1 or VCR 2 to control the desired Palmcorder. For VCR 2 Press these buttons at the same time. 1 2 З Set POWER to VCR or CAMERA. • The POWER Lamp lights red. • Be sure POWER is fully turned to VCR or CAMERA position. Press MENU to display the VCR or CAMERA mode menu screen. For VCR 1 : Press these buttons at the same time. When the Palmcorder and remote are not set to the same mode (VCR1 or VCR2), “CHECK REMOTE MODE (REMOTE)” will appear. 4 б Rotate JOG KEY to select SET-UP in the CAMERA mode menu screen or PLAY MODE in the VCR mode menu screen, then press JOG KEY to display the CAMERA SET-UP or VCR PlAy MODE menu screen. REMOTE Rotate JOG KEY to select and then press JOG KEY to select VCR 2 (Menu OSD: pp. 109, 110). Leave the other Palmcorder set to VCR1. Set the Remote Control to VCR 1 or VCR 2 to correspond with the Palmcorder you wish to control. (See above left.) After replacing the Remote Control Battery, the remote will default to VCR 1. B Note 10 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to: consumerproducts@panasonic.com Quick Guide Insert the Battery Pack r Before you begin — [ • Charge the Battery. (p. 14) Insert Cassette These Palmcorders are equipped with the Easy Cassette Eject System so it is easy to insert or remove tapes, even when on a tripod. (p. 7) 1 Press LCD-OPEN to unlock the LCD monitor, and swing it fully open. 2 Set POWER to VCR or CAMERA. 5 Press PUSH TO CLOSE mark to close the Cassette Compartment Cover. Slide TAPE EJECT to open the Cassette Compartment Cover. Insert a cassette record tab up, window side facing out. • Make sure the record tab is closed. (p. 7) 11 Before Use Quick Guide Camera Recording When the LCD monitor is fully open, the Viewfinder automatically turns OFF. 1 2 Adjust the Vision Adjustment Control to your eyesight. 4 Press REC/PAUSE to start recording. Press REC/PAUSE again to pause recording. 3 LCD Monitor Press LCD-OPEN to unlock the LCD monitor. Swing it fully open and adjust the angle. To Watch Playback in the LCD (Liquid Crystal Display) When the LCD monitor is fully open, the Viewfinder automatically turns OFF. Before you begin- • Charge the Battery. (p. 14) 2 3 Press LCD-OPEN to unlock the LCD monitor. Swing it fully open and adjust the angle. Press <44 (REW) to rewind the tape Set POWER to VCR. 4 5 Press (PLAY) to start playback. Press ■ (STOP) to stop playback. 12 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to: consumerproducts@panasonic.com Quick Guide r Before you begin — [ • Charge the Battery. (p. 14) *Memory Card: MultiMediaCard or SD Memory Card (p. 94) • Be sure to insert the Memory Card before using the Card PhotoShot. (p. 48) Below is a list of memory cards which can be used in this Palmcorder. Insert Memory Card* Memory Card Capacity SD Memory Card (RP-SDOO8BMKO) (supplied) 8 MB MultiMediaCard (SanDisk brand) 8 MB, 16 MB SD Memory Card (optional) (p. 92) 16 MB, 32 MB, 64 MB SD Memory Card write protection switch A write protection switch is located on the SD Memory Card. Sliding the switch to the “LOCK” position prevents writing on or formatting the card. 1 Write protection Switch Set POWER to OFF. 2 Slide DOOR OPEN to open M-CARD door. To remove the Memory Card... Press here to eject the card. About the M-CARD Lock Switch POWER 3 4 Insert the Memory Card and hold in place until you hear a click. Close the M-CARD Door. When inserting the Memory Card ■ By sliding M-CARD Lock to LOCK, you can prevent POWER from accidentally entering the M-CARD position w...