Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
[ADJUSTMENT by CAMERA] 3. In normal shooting mode: Press the ITEM/AWC switch for over 2 second. ITEM/AWC Switch – + MENU ITEM/AWC YES/ABC NO/BAR OPTION CARD VIDEO OUT I/F REMOTE G/L IN IRIS DC12V IN CAMERA [ADJUSTMENT with the RCU (RCB, Hybrid control panel)] 4. When the AUTO set switch is turned to AWC, the white balance will be automatically set. While the system is being set, auto warning indicator (LED) blinks and it goes out when the white balance setting is completed. If the lamp remains lit, the setting must be tried again. RCU (RCB) AUTO LED R B R BPED TOTAL PEDA B ATW AWC AUTO HOLD ABC AUTO/ATW PAINTING GAIN AUTO set switch -21 Notes: • For white balance setting aim the camera at a white object and try to position it in the center of the monitor screen. The object must appear in over 10 % of the total monitor screen area. Try to avoid overly bright objects in the scene. • White balance may not be correctly set if the lighting of the object is too weak. The white object must occupy over 10 % of the monitor screen area. ........................................ • Since the camera has a built-in memory, the set white balance will remain in the memory even if power is turned off. Therefore, it is not necessary to reset the white balance if the color temperature of those objects remains unchanged. However, it must be reset if the color temperature changes, such as when you move from indoors to outside, or vice versa. • When the camera is used without a RCU or RCB red/blue gain adjustment of painting setting will be automatically reset to ±0 after setting the white balance. (painting setting in only USER MODE.) -22 ¦ AUTOMATIC TRACKING WHITE BALANCE SETTING (ATW) White balance will be automatically set to continuously match changes of light source and color temperature while the white balance setting is set to ATW. Note: White balance may not be accurately set if there is no white object in the scene being shot. ¦ MANUAL WHITE BALANCE SETTING [ADJUSTMENT by CAMERA] Manual setting is possible in USER MODE only. 1. Select the white balance mode either AWC A or AWC B by menu. 2. Aim the camera at a large white object. Press the Item/AWC switch for over 2 second. 3. Adjust the red gain/blue gain control in the PAINTING item of Color Set sub menu of USER MODE until the carrier wave of the white portion of the video signal is at the minimum width or the white object in the monitor screen appears pure white. (Use an oscilloscope or a waveform monitor for precise adjustment.) [ADJUSTMENT with the RCU (RCB)] After AWC setting, adjust the R/B GAIN controller in the same way as described in Step 3 above. Minimize the carrier wave using the red & blue gain controls Waveform for white balance set chart ¦ RESET TO 3 200K OR 5 600K WHITE BALANCE When the white balance setting is set to either “P SET 3 200K” or “P SET 5 600K” the white balance will be automatically set to the color temperature 3 200K or 5 600K, respectively. BLACK BALANCE ADJUSTMENT • Close the lens. If the motor drive lens is controlled from the camera, the lens is automatically closed when the black balance is adjusted. • When the camera is used without a RCU or RCB, R/B pedestal adjustment of painting setting will be automatically reset to ±0 after setting the black balance. (painting setting in only USER MODE.) [ADJUSTMENT by CAMERA] Press the YES/ABC Switch for over 2 seconds and the black balance will be set automatically in 10 seconds. In user mode, black balance fine adjustment can be performed with the red pedestal/blue pedestal setting after setting the black balance. [ADJUSTMENT with the RCU (RCB, Hybrid control panel)] Set the AUTO set switch to ABC and the black balance will be automatically set. While the system is being set, the auto warning indicator (LED) blinks and it goes out when the black balance setting is completed. If the lamp remains lit, ABC should be tried again. OPTION CARD VIDEO OUT I/F REMOTE MENU G/L INITEM/AWC YES/ABC + IRIS NO/BAR YES/ABC Switch – DC12V IN AUTO LED PAINTING AUTO/ATW GAIN ATW TOTAL RB A PED B AUTO PED AWC HOLD RB AUTO ABC set switch ABC -23 ¦ TOTAL PEDESTAL LEVEL ADJUSTMENT (Use an oscilloscope or a waveform monitor for this adjustment.) This step is to adjust the black levels (pedestal levels) of two or more cameras to be the same. [ADJUSTMENT by CAMERA] 1. Close the lens. 2. Select Pedestal item in the brightness setting Sub Menu (Select [Pedestal] in the [Iris, Shutter, Gain Set] sub menu in USER MODE.) 3. Set the pedestal level to 5 IRE (0.035 V) with the YES/ABC switch or the NO/BAR switch. 5 IRE (0.035 V) [ADJUSTMENT with RCU (RCB, Hybrid control panel)] Adjust the pedestal level to 5 IRE with the total pedestal adjustment. **Brightness Set** Picture Level ±0 Light PEAK/AVG 0 Light Area Top cut Auto ND (ELC) OFF Auto Gain Up OFF Manu Gain Up 0dB Pedestal ±0 Contrast(Gamma) MID Return – + MENU ITEM/AWC YES/ABC NO/BAR OPTION CARD VIDEO OUT I/F REMOTE G/L IN IRIS DC12V IN NO/BAR switch YES/ABC switch R...