Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Lights in the counter memory mode (0000 stop mode). The counter memory mode is set using the menu item. Lights in the S-VHS mode. This denotes that a cassette tape has been loaded. 18 □ E! □ Counter This indicates the time code and user bit data in units of hours, minutes, seconds and frames. It serves as a 4-digit counter in the reel count mode. REMAIN О О ’ О О • О О * О О U U • U U • U U * U U i h i min i s i frm i Remaining battery level display This indicates the remaining battery level. The battery is set using the menu item. For further details, refer to "How to set the menu items” (page 52). Different kinds of batteries and their operating times are shown in the table below. (The operating times shown apply when the unit is used in the continuous recording mode.) Bear in mind that the actual operating time will vary greatly depending on what shooting methods are used, whether old or new batteries are used and on other such conditions. Battery Operating time (during continuous recording) Model number Manufacturer Capacity TRIMPAK 14 DIGITAL Anton/Bauer 40 WH 90 minutes DIGITAL HD MAG 14 Anton/Bauer 60 WH 160 minutes AU-BP402 Panasonic 4 AH 140 minutes AU-BP220 Panasonic 2.2 AH 70 minutes NP-1B SONY 2.3 AH 70 minutes Warning displays RF: Flashing denotes that the video heads are clogged. SERVO: Flashing denotes that the servo system is not locked. HUMID: Flashing denotes that condensation has formed on the cylinder. SLACK: Flashing denotes tape slack or some other problem in the tape transport system. END: Flashing denotes that the tape has come to its end. 19 Viewfinder display LED displays o o o AUDIO TALLY STBY GAIN BATT VTR O O O AUDIO (yellow): Not used by this system. TALLY (red): Lights during recording; flashes during tape approach. STBY (green): Lights in the power save mode. GAIN (yellow): Lights when the camera gain is increased or the camera AGC mode is established. BATT (yellow): Flashes when the battery has run down. VTR (yellow): Lights or flashes when trouble has developed in the VTR. Character displays (normal displays) Audio CH1 level i meter Audio CH2 level meter VTR status display Super iris display (appears in the super iris mode) Lens f-number display ......+++ Super Iris F2.8 * ►......+++ 12.5 V- -PAUSE TCG 00:00:00- 02-21 -94 17:35:10 Date display Time display Battery voltage display Counter display •These display appear when the CHARACTER switch on the front of the viewfinder is at the ON position. • Each of the display can be turned OFF using the menu settings. 20 Character displays (displays when changes have occurred) ......+++ SuDer Iris F2.0 ......+ + + Camera warning ] 2.5V display | Filter display | | AWB/ABB operation display~| | AWB memory display | j Electronic shutter speed display | | Scene file display] | VTR warning display | PAUSE TCG 00:00:00 08-21-94 17:35:10 •Camera warning display A warning message appears when AWB or ABB has not been set properly. • Filter display The filter number and name are displayed for about 3 seconds when the CC filter setting is selected. •AWB/ABB operation display "ACTIVE” appears while the AWB or ABB operation is in progress. “OK" appears upon completion of the operation. •AWB memory display This indicates the AWB channel A and B memory statuses and switch status. The displays appear for about 3 seconds when the AWB switch setting is selected. •Electronic shutter speed display This indicates the electronic shutter speed. When the electronic shutter has been selected or the shutter speed has been changed, the display appears for about 3 seconds. •Scene file display This indicates the name of the present scene file for about 3 seconds when the scene file selector button is pressed. •VTR warning display This appears when trouble has occurred in the VTR. 21 14x Power Zoom Lens Automatic Iris Control Lens Iris Selector Switch [IRIS] A: M: This enables the automatic iris speed to be adjusted. The control can be found inside when the rubber cap is removed. The speed is increased by turning the control clockwise but bear in mind that turning it too far will cause hunting (the operation does not stop). Be absolutely sure to adjust the control when replacing the lens or when attaching the lens for the first time. The iris is adjusted automatically. For adjusting the iris manually. Note: When the camera’s AGC function has been activated, the iris is adjusted automatically even if this switch is set at the [M] position. Power Zoom Control Switch □ Hand Strap Return Switch [RET/REC CHECK] The zoom can be controlled electrically by setting the power/ manual zoom selector switch to SERVO and by pressing this control switch. The zoom speed changes according to how firmly the switch is pressed. Adjust the strap to fit the size of your hand. This switch is used to check recordings. When it is pressed during recording pause, the recording check functio...