Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
You can view or record ONLY the channels you have selected on the cable box or the satellite box. • While you are recording, only the recorded channel can be viewed. To select channels of the cable box or satellite box 1) Turn on the unit by pressing [STANDBY-ON], then press [VCR/TV]. The “POWER” and the “VCR/TV” indicator on the front panel will appear, then press [CHANNEL ] to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box). • If you use the channel 4, you need to change the unit’s RF output to channel 4. Refer to “RF Output Channel”. 2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1). 3) On the cable box or satellite box, select the channel you want to view or record. You can use the AUDIO OUT jack and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. In this case, you need to set the TV to external Line Input Mode. Please refer to your TV’s owner’s manual. Owner’s Manual Video Cassette Recorder CMWV405 1VMN22462 / HJ34RCD ..... Printed in China ANT IN jack Connect your antenna or cable box here. ANT OUT jack Connect the supplied RF cable to the antenna input jack on your TV. Front & Rear Terminals Stereo TV Connection • Remote control (NA374UD) with two AA batteries • RF cable (WPZ0901TM002) • Owner’s manual (1VMN22462) Supplied Accessory Installing the Batteries for the Remote Control Install two AA batteries (supplied) matching the polarity indicated on the bottom of the remote control. If channel 3 is already occupied for broadcasting, 1) Set your TV to channel 4. 2) Insert a pre-recorded tape into this unit. 3) Press [PLAY B] once. 4) After a few seconds, hold [PLAY B] on the unit for 3 seconds. • The RF output channel will change to channel 4 from channel 3 and you will see a playback picture. • When a picture does not appear on the TV screen, repeat step 4. 5) Press [STOP C] to stop playback. Hint • The RF output channel does not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, hold [PLAY B] on the VCR for 3 seconds again. VIDEO OUT jack Connect the video cable here through the video input jack of a camcorder, another VCR or a TV. RF Output Channel VIDEO AUDIO STANDBY-ON STOP/EJECT REW F.FWD IR POWER VCR/TV CST.IN TIMER RECORD CHANNEL MENU RECORD PLAY 1. Before Using Your VCR ANT IN OUT RF Cable (supplied) (Back of VCR) (Back of TV) (Back of TV) 4 Plug the AC power cords of the VCR and TV into the AC outlets. Disconnect Antenna or 2 Connect 3 Connect Antenna or Cable TV Signal Cable TV Signal RF Cable (not supplied) RF Cable (not supplied) Basic TV Connection Hint for Cable Box or Satellite Box ANT IN OUT ANT IN OUT RF cable (supplied) RF Cable (supplied) RF Cables (not supplied) RF Cable (Back of VCR) IN OUT E (Back of TV) (Back of TV) IN OUT (Cable box or Satellite box) Cable E Signal Connection B Antenna or Cable TV signal (Back of VCR) (Cable box or Satellite box) If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call TOLL FREE : 1-800-605-8610 AUDIO OUT jack Connect the audio cable here through to the audio input jack of a camcorder, another VCR, a stereo amplifier or an audio system. ANT AUDIO VIDEO IN OUT OUT IN ANT AUDIO VIDEO IN OUT OUT IN ANT IN OUT AUDIO ANT IN OUT VIDEO Audio/Video Cables (not supplied) AUDIO IN VIDEO IN AUDIO IN VIDEO IN (Back of TV) OUT IN (Back of VCR) AUDIO IN jack Connect the audio cable coming from the audio output jack of a camcorder, another VCR or an audio source here. • To use the input jacks on the back of this unit, press [0], [0], [1] on the remote control. • To use the input jacks on the front of this unit, press [0], [0], [2] on the remote control. VIDEO IN jack Connect the video cable coming from the video output jack of a camcorder, another VCR or an audio-visual source (laser disc player, video disc player, etc.) here. 2. IMPORTANT SAFEgUARDS WARNINg: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 1. Read Instructions-All the safety and operating instructions should be read before the applianc...