Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
VOH560PKG Drop Down Video Monitor and Video Cassette Player System Installation and Operation Manual Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle. Please note that the state of Rhode Island forbids the installation of such a device in a motor vehicle. MATERIALS INCLUDED IN THIS PACKAGE: 1)VOH560 Video Monitor with out TV Tuner (1 pc) 2)VCP Harness (P/N 112C3035) (1 pc) 3)12 Pin Power / Signal harness (P/N 112B2821) (1 pc) 4)2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc) 5)Hardware Package for VOH560 #4 x 3/8” Screws (12 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 6)Remote Control (P/N 136C1957)(1pc) 7)Left Protective Cover for External A / V Inputs (P/N 102B3596) (1pc) 8)Right Protective Cover for Headphone Jacks (P/N 102B3597) (1pc) 9)Mini Console (P/N 102D3595) (1pc) 10)AVP756 Video Cassette Player (1pc) 11)Hardware Package for AVP756 #4 x 3/8" Screws (4 pcs) Mounting Bracket (2 pcs) -1- TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim ring if used) Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to vehicle) Video tape (to verify system operation after installation) CHOKE 3e 3c A A A A A A . C E E 11 PICTURE SELECT . + WIRED HEADPHONE VOLUME CONTROL POWER PLAY REW FWD STOP VIDEO or GAME REPLAY AU D IO R AU D IO L V ID EO P OW E R S TO P /E J E CT REW P LA Y F F RE P E AT 3c GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, RF Modulator/external amp, remote headphone, 2nd VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harnesses will need to be located. If any access holes need to be cut into the vehicle (headliner, other trim components etc.), this should be done now as well. (Refer to Page 3). 5) Route the wiring harnesses through out the vehicle as necessary. (Refer to the Wiring Diagrams on page 6 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. 6) Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations. 7) Connect all components together (electrically) and verify proper operation of all system functions. Note: This is best done BEFORE, components have been permanently mounted. 8) After verifying proper operation of the system, proceed to mount each component. 9) When all components are mounted, recheck function of entire system again to ensure that no wiring was pinched or connected improperly during final installation. GENERAL SYSTEM CONFIGURATION: The following is intended to give a rough guideline of system configuration that are possible with the VOH560PKG Drop Down Video System: System : Video Monitor without tuner (VOH560), VCP (AVP756). -All wiring necessary is included with this package. -Headphone is connected into the headphone jack on the monitor itself. Notes: -There are a few audio output options that can be added as follows: a) Additional speakers can be added to a VOH560 using the speaker outputs. Refer to the wiring diagram on page 6. -The VOH560 is only intended for an overhead, drop down installation. It is not intended for seat back or any other type of mounting. The hinging mechanism is designed for horizontal, drop down use only. -2 VEHICLE PREPARATION: 1) Locate a constant power source (+12v at all times) and an accessory power source (+12v when key is in the acc. and run positions, and 0v when key is off). Generally, these wires can be found at the ignition switch or fusebox. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is installed. The monitor should be located in such a manner that it can be ...