Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Then, press [F.FWD]. Next, select "HIFI" or "MONO" by pressing [PLAY] or [STOP]. To exit, press 2) [EXIT/RESET]. • While the VCR is set in HIFI stereo mode, HIFI appears on the TV screen. While the VCR is set in monaural (MONO) mode, HIFI disappears from the TV screen. MTS RECORDING/MONITOR MODE Type of broadcast Display on the TV screen STEREO/SAP Selection Hi-Fi audio track (2-channel) Normal audio track Regular (monaural audio) -None- InvalidL- channel R-channel Mono Mono Mono Stereo broadcast STEREO I-nvalid-L R L+R Bilingual broadcast SAP TV STEREO* Main audio program Main audio program Main audio program SAP* Sub audio program Sub audio program Sub audio program Stereo & Bilingual broadcast STEREO SAP TV STEREO* L R L+R SAP* Sub audio program Sub audio program Sub audio program * You must select the recording mode in TV STEREO or SAP before you record a broadcast. REAL TIME TAPE COUNTER • This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change during blank portions on the tape.) • The indication will appear when the tape is rewound further than “0:00:00” on the tape counter. AUTO REWIND When a tape has reached the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape and turn itself off. • The VCR will not rewind the tape automatically during timer recording or One Touch Recording. • When the Counter Memory is activated, the tape will rewind to the M0:00:00 and the VCR will go into the Stop mode. REMOTE CONTROL OF THE CABLE CONVERTER PROGRAMMING 1) Hold down the CATV button. 2) Press the number button of your brand of cable box. (shown in the chart) OPERATING 1) Press the CATV button. 2) Press the button of the function you want. 3) Press the VCR button to operate your VCR with the remote again. Brand Number Jerrold1 1 Jerrold2 2 Jerrold3 3 Hamlin 4 Zenith 5 Scientific Atlantic 6 Pioneer 7 Philips 8 REMOTE CONTROL OF THE TV PROGRAMMING 1) Turn on the TV. 2) Press the number button of your brand of TV. (shown in the chart) OPERATING 1) Press the TV button to change to the TV function mode. 2) Press the button of the TV function you want. 3) Press the VCR button to operate your VCR with the remote again. Brand Number Hitachi 1 Zenith 2 Sony 3 Magnavox 4 Sanyo 5 Gold Star 6 Toshiba 7 Funai 8 Panasonic2 9 RCA 0 Panasonic1 CH(K) Mitsubishi CH(L) JVC +100/ENTER Sharp1 MEMORY Sharp2 DISPLAY TROUBLESHOOTING GUIDE If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem. PROBLEM CORRECTIVE ACTION No power. • Make sure the power plug is connected to an AC outlet. • Make sure the power is turned on. Timer recording is impossible. • Make sure the timer recording is set correctly. • Make sure the power is off. • Make sure the VCR clock is set correctly. Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape. Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNEL ] on the VCR. ( ) Cannot view a tape but the audio is OK. • Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” . • Make sure the VCR is not in the Menu mode. No or poor playback picture. • Select channel 3 or 4 at your TV, then press [VCR/TV] so that the VCR indicator on the VCR comes on. • Fine tune your TV. TV programs cannot be seen normally. • Re-check the ANT. IN and ANT. OUT connections. See page 3. • Press [VCR/TV] so that the VCR indicator on the VCR disappears. No VCR operation from the infrared Remote Control. • Make sure the power plug is connected to an AC outlet. • Check batteries in remote control. • Press VCR button on the remote control, then try again. Video or color fades in and out when making a copy of a video tape •You cannot copy a copyrighted video tape.You are experiencing copy guard protection. MAINTENANCE AUTO HEAD CLEANING • Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture. • Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your VCR may need to be cleaned. 1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner. 2. If a Video Head Cleaner does not solve the problem, consult our nearest Authorized Service Center. Professional video head cleaning requires highly technical attention. SERVICING Should your VCR become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please take ...