Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3) Press the PLAY button once. 4) After a few seconds, press the PLAY button on the VCR for 3 seconds. • The RF output channel will change to channel 4 from channel 3 and you will see a playback picture. • When a picture does not appear on the TV screen, repeat step [4]. 5) Press the STOP button to stop playback. You can use the AUDIO OUT jacks and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. In this case, you need to set the TV to external Line Input Mode. Please refer to your TV’s owner’s manual. - 1 - Owner’s Manual Video Cassette Recorder EWV603 If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call TOLL FREE : 1-800-256-2487 or visit our web site at 0VMN03902 / HF440UD ..... Printed in China ANT AUDIO VIDEO IN OUT OUT IN OUT L R IN ANT AUDIO VIDEO IN OUT OUT IN OUT L R IN AUDIO IN jacks Connect the audio cables from the audio out jacks of a camcorder, another VCR, or an audio source. VIDEO IN jack Connect the video cable from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.). AUDIO OUT jacks Connect the audio cables to the audio in jacks of a camcorder, another VCR, a stereo amplifier, or an audio system. ANT IN jack Connect your antenna or cable box. ANT OUT jack Connect the RF cable (supplied) to the antenna input jack on your TV. Front & Rear Terminals Stereo TV Connection ANT IN OUT AUDIO ANT IN OUT VIDEO OUT L R IN Connect 1 Audio/Video Cables (not supplied) L R VIDEO AUDIO OUT OUT L R VIDEO AUDIO IN IN (Back of TV) OUT IN (Back of VCR) • Remote control (NA372UD) with Two AA batteries • RF Cable (WPZ0901TM002) • Owner’s Manual (0VMN03902) Supplied Accessory Installing the Batteries for the Remote Control Install two AA batteries (supplied) matching the polarity indicated on the bottom of the remote control. Hiintt • The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, press the PLAY button on the VCR for 3 seconds again. VIDEO OUT jack Connect the video cable to the video in jack of a camcorder, another VCR, or a TV. RF Output Channel EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A. CHANNEL MENU POWER REC/ TAPE IN VIDEO L-AUDIO-R POWER VCR/TV TIMER REC 1. Before using your VCR ANT IN OUT RF Cable (supplied) (Back of VCR) (Back of TV) (Back of TV) 4 Plug the AC power cords of the VCR and TV into the AC outlets. Disconnect Antenna or 2 Connect 3 Connect Cable Signal Antenna or Cable Signal Basic VCR/TV Connection Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the VCR.You can view or record ONLY the channels you have selected on the cable box or the satellite box. • While you are recording, only the recorded channel can be viewed. To select channels of the cable box or satellite box 1)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button.The POWER and the VCR/TV indicators on the front panel will light on. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box). • If you use the channel 4, you need to change the VCR’s RF output to channel 4. Refer to “RF Output Channel”. 2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1). 3) At the cable box or satellite box, select the channel you want to view or record. Select this connection when you want to change channels on the VCR. With this connection, you may watch one channel while recording another. • You may not view or record a scrambled channel. To select channels of the cable box or satellite box 1)At the cable box or satellite box, select channel 3 or 4 (the same channel as the VCR’s RF output channel.) • Refer to “RF Output Channel”. 2)At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box. 3)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button .The POWER and VCR/TV indicators on the front panel will light on. Then, select the channel you want to view or record. To play back a tape Follow the steps 1) to 2) above. Then, play back a tape. • Refer to “Playback” on page 5. To view one channel while recording another 1)While you are recording on the VCR, press the VCR/TV button so that the VCR/TV indicator disappears on the VCR. 2)At the cable box or satellite box, select the channel you want to view. Hint for Cable Box or Satellite Box ANT IN OUT RF Cable (supplied) (Back of VCR) IN OUT E (Back of TV) Cable Signal Connection A (Cable box or Satellite box) ANT IN OUT RF Cable (supplied) RF Cable(Back of TV) IN OUT (Cable box or Satellite box) Cable E Signal Connection B (Back of VCR) 2. Important WARNING: TO REDUCE ...