Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
All the fittings supplied are to be found in a polythene bag inside the carton. IMPORTANT: Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas pipes before drilling. If it is necessary to fix the hood to a hollow construction plaster or partition board structure then it must be sufficiently reinforced to be quite rigid in the area of the cooker hood mounting brackets. The hood must not be fitted using the key hole fixing points but with the special brackets supplied. Use the paper template provided to mark the hole positions on the wall for the bracket fixing screws. Check the hole distances are correct with a tape measure as stated on the template. At this stage it is important to allow 15mm (1/2") clear space above the cooker hood to enable it to be hooked onto the brackets and for subsequent removal for decorating or servicing. When drilling the holes for the wall fixing brackets care must be taken to ensure that they are quite level as there is minimal vertical height adjustment of the fixing brackets. The brackets should be fitted with the round end at the bottom using the plastic rawl plugs and screws provided. If the brackets are to be fitted to a hollow plaster or partition board structure then the plastic rawl plugs provided should not be used. Once the brackets are secured lift the hood squarely to the wall slightly higher than the brackets and lower the cooker hood until the cooker hood locates onto the two brackets. Ensure that the cooker hood is correctly located before letting go. Access to the two wall levelling screws and the security fixing system will require the removal of the lower inlet grille that supports the grease mat filter. To remove the lower grille press inwardly on the two slide catches located towards either side of the grille near the front and the grille will open from the front. The grille pivots at the rear. Slide the right edge of the grille forward until it clears the guide and then unhook the left hinge pin. Care should be taken to fully support the grille when removing it from the guides. The two wall levelling screws will be visible toward either end of the back panel, when the grille has been removed. Turn the screws clockwise to lift the front edge of the hood and use a spirit level to check the hood is positioned at right angles to the wall before fitting the security system. 5 INSTALLATION Cont'd DUCTING FITTING The wall brackets have two studs and when the cooker hood is hung onto the brackets the studs project through the two holes above the levelling screws. When the hood is level fit the two shakeproof washers and nuts supplied to fully secure the cooker hood. Wall Cabinet Fitting Before fitting the cooker hood beneath any type of wall cabinet ensure it is firmly fixed to the wall in accordance with the manufacturers instructions. Use the paper template provided to mark the hole positions on the underside of the cabinet. When marking the underside of the cabinet the front edge of the template must be aligned with the front edge of the cabinet carcase. Check the distances of the holes are correct with a tape measure as stated on the template. The four holes are 5mm (1/4") dia. A pad saw or similar cutter will be required to cut the circular hole for the ducting spigot if it is to be used. Insert the fixing screws through the holes from inside the cabinet. Supporting the cooker hood tighten each screw about half way to ensure that the cooker hood is correctly positioned before fully tightening the screws. If the hood is to be ducted to the outside then the blanking plate supplied must be fitted in the aperture that will not be used. Fit the ducting spigot into the selected aperture and make an air tight connection. The ducting used must be 100mm (4") diameter, manufactured from fire retardent material conforming to the relevant British Standard or DIN 4102-B1. Where flexible ducting is fitted it should not be turned through very tight bends as this could impair the performance of the hood. To fit the ducting spigot and blanking plate align the inter-locking lugs on the fitting with the recesses in the aperture and insert turning clockwise to lock the spigot and blanking plate into position. (The maximum length of ducting including one 90 Degree bend should be 3 metres, to be reduced by 1 metre for each 90° bend installed in the duct run). When the ducting mode is selected the optional charcoal filter is not required. 6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Cont'd The cooker hood functions are controlled by two slide switches and a change-over slider control. The two slide switches, which are located on the right hand side in the front fascia panel, control the fan speed and worktop illumination. The change-over slider control is located inside the cooker hood behind the inlet grille immediately in front of the lamp assembly. Ensure the hood is plugged in,...