Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: CFM Dateigröße: 1.7 mb Dateiname: Manual20of20Hyd-14A.pdf Unterrichtssprache:

1 clevis pin) b) Electrical hardware (3 plastic wire connectors. 2 pull chain for the fan. 1 pull chain for the light kit). Unpacking Your Fan 2. Tools Required Phillips screw driver, straight slot screw driver, adjustable wrench, step ladder, and wire cutters. Mounting Options If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs.). Do not use plastic outlet boxes. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK. OR OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES MAY NOT BE ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT. Figures 1 and 2 are examples of different ways to mount the outlet box. existing fixture but no ceiling joist, you may need an installation hanger bar as shown in Figure 3. 3.hi stalling Your Fan Hanging the Fan STANDARD CETLING MOUNTING I. Remove the canopy ring from the canopy by turning the ring to the right until it unlocks. (Figure 4)_ Figure 4 2. Remove the hanger brackct from the canopy by loosening the four screws on the top of the canopy. Remove the two nou-slolted screws and loosen the slotted screws. This will enable you to remove Route the wires exiting the fan motor through collar and dounrod. Ik' cardul 1101 to jam the motor colar cover, then the canopy ring. Make the boll agaiiN ilie Hiring inside ilic sure the slot openings are on top. Route the wires dowmod. Inseil ele\is pin and bend lu through the canopy and then through the ball/ ensure seciiriu. as noted in I he circle nisei downrod assembly. (Figure 6) Figure 6 of Figure 6. 6. Tighten the two screws on top of the fan motor firmly and slide down the motor collar cover._ WARNING FAILURE TO PROPERLY INSTALL LOCKING PIN AS NOTED IN STEP 5 COULD RESULT IN FAN LOOSENING AND POSSIBLY FALLING. CFL 4. Loosen, bul do not remove, the 2 set screws on tlie collar on the top of the ccnter housing. 5. Align the holes at the bottom of the downrod with holes in tile collar on top of the motor housing (Figure 6 I. Carefully insert the boll through the holes in the 4. Installing Fan to the Electrical Box 1. Pass the 120-volt supply wires through the center hole in the cciling mounting plate as shown in Figure 7. 2. Install the ceiling mounting plate on the electrical box by mounting screws provided with the outlet box. Note that the flat side of the mounting plate is toward the electrical box (Figure 7). 3. Securely tighten the two mounting screws. 4. Carefully lift the fan assembly up to the cciling mounting plate and hang the fan on the hook provided by utilizing one of the holes at the outer rim of the cciling canopy (Figure 7). Scat the hanger ball in canopy. Make sure the tab in the ring at the bottom of the canopy is properly seated in the groove in the hanger ball (Figure 8). Standard Mounting Figure 8 WARNING THE HOOK AS SHOWN IN FIGURE 7 IS ONLY TO BALANCE FAN WHILE ATTACHING WIRING. FAILURE TO HANG AS SHOWN IN FIGURE 8 MAY RESULT IN HOOK BREAKING CAUSING THE FAN TO FALL. HOOK MUST PASS FROM INSIDE TO OUTSIDE OF CANOPY. WARNING WHEN USING THE STANDARD BALL/HANGER PIPE MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL.FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. Figure 7 UL Listed Electrical Box Mounting Screws (supplied with Electrical Box) Hook 5. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE A SOLID STATE SPEED CONTROL WITH THIS FAN. IT WILL PERMANENTLY DAMAGE THE ELECTRONIC CIRCUITRY Making the Electrical Connections REMEMBER lo disconncct the power. If you feel that y...

Herunterladen

Geben Sie zwei Ziffern: