Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. • Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood. • For Class I appliances, check that the domestic power supply guarantees adequate earthing. • Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible. • Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.). • If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. USE • The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. • Never use the hood for purposes other than for which it has been designed. • Never leave high naked flames under the hood when it is in operation. • Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. • Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. • Do not flambe under the range hood; risk of fire • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • Children should be supervised to ensure that they do not play with the appliance. MAINTENANCE • Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. • Clean and/or replace the Filters after the specified time period. • Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. CHARACTERISTICS Dimensions EN 4 EN 55 Components Ref. Q.ty Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filters 2.1 1 Upper Section 2.2 1 Lower Section 8 1 Directional Air Outlet grille 9 1 Flange 10 1 Adapting ring o 120-125 mm 14.1 2 Air Outlet Connection Extension 15 1 Air Outlet Connection 16 1 Filter cover Ref. Q.ty Installation Components 7.2.1 2 Upper Chimney Section Fixing Brackets 7.3 1 Air Outlet Connection Support 11 6 Wall Plugs 11a 2 Wall Plugs SB 12/10 12a 6 Screws 4,2 x 44,4 12c 10 Screws 2,9 x 6,5 12d 2 Screws 2,9 x 9,5 Q.ty Documentation 1 Instruction Manual INSTALLATION Wall drilling and bracket fixing 7.2.1 X 1.2 11a 11 12a 112+AA=Min 250 Max 400 710+A 1 2 1 2 200 200 180 180 A 7.3 On the wall, draw • a Vertical line up to the ceiling or upper limit, at the centre of the area in which the Hood is to be fitted; • a Horizontal line at a minimum of (710 mm + A) above the Cooker Top. • Mark a point (1) on the horizontal line, 200 mm to the right of the vertical reference line. • Repeat this operation on the other side, checking that the two marks are level. • Mark a reference point (2) as indicated at 180 mm from the vertical reference line and (112 mm + A) above the Cooker Top. • Repeat this operation on the other side, checking that the two marks are level. • Drill at the points (1) marked, using a o 12 mm drill bit. • Drill at the points (2) marked, using a o 8 mm drill bit. • Insert the bracket plugs 11a into the holes 1 and screw into place. • Insert plug 11 into hole 2. To install a decorative chimney ( optional ) • Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. • Mark the wall at the centres of the holes in the bracket. • Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. • Mark the wall at the centres of the holes in the bracket. • Drill o 8 mm holes at all the centre points marked. • Insert the wall plugs 11 in the holes. • Fix the lower bracket 7.2.1 using the 12a screws (4,2 x 44,4) supplied. • Fix the upper bracket 7.2.1 and the air outlet con...