Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
COOKTOP POWER -The Cooktop POWER key pad activates the entire Cooktop. To power the cooktop, touch and hold the POWER key pad. A beep will sound and the Power LED will glow (See Fig. 4). The cooktop will be in a ready mode. If no other key pads are touched the Cooktop Main POWER will turn OFF automatically. To turn the Main Power OFF touch and hold the Main POWER key pad. A beep will sound and the Power Indicator Light will turn OFF (See Fig. 3). ERRORS CODES XX -The Minute Timer display digits showing an error code. “E - E -E -E -E -E -” (Fig. 5) and a two digit number error code (Fig. 6) will flash in turn in the Minute Timer display. LIGHT INDICATORS DISPLAYED BY COOKING ELEMENT CONTROLS COOKING ZONE ON/OFF PAD - Each Cooking Elements have separate ON/OFF key pads. Once the Main Power key pad has been touched to activate the cooktop, touch the corresponding Cooking Element ON/OFF key pad once to active the Cooking Zone needed. The indicator light located above the key pad will glow (Fig. 8). If the corresponding hi + (increase), med or - lo (decrease) key pad is not touched, the request to turn the Cooking Element ON will cancel and the Cooktop Main Power will turn OFF. To set a Cooking Element power level touch the corresponding Cooking Element hi + (increase), med or - lo (decrease) key pad once. To turn OFF a Cooking Element, touch the Cooking Element ON/OFF key pad once. The Cooking Element Indicator Light will turn OFF (Fig. 7). HOT SURFACE INDICATOR LIGHT -After using any of the single, dual or triple radiant element positions the cooktop will become very hot. Even after turning the control to OFF, the cooktop will remain hot for some time. The hot surface indicator light will turn on (Fig. 9) if the cooktop is still hot and will remain on until the heating surface area has cooled sufficiently. If the indicator light is on, the control can still be turned ON again for use. lock lock POWER POWER ON OFF ON OFF 12 Setting Surface Controls Fig. 1 Fig. 2 Fig. 3 med Fig. 5 med 1 2 3 4 5 6 7 Fig. 9 - Power levels med Fig. 5 med 1 2 3 4 5 6 7 Fig. 9 - Power levels LIGHT INDICATORS DISPLAYED BY COOKING ELEMENT CONTROLS size size ELEMENT SIZE INDICATOR LIGHTS -Some cooking elements offer 2 or 3 different element sizes. You may choose to use the single inner heating ring only or you may add 1 or 2 more heating rings with each press of the pad. When the element zone is size activated, the inner heating ring indicator light will glow (Fig. 1). When the element size pad is pressed once, the inner and middle ring indicator lights will glow (Fig. 2). And when the element size key pad is pressed twice, all the element size indicator lights will glow (Fig. 3). When the element size is at its maximum and the element size key pad is size med pressed, the inner heating indicator light only will glow (Fig. 1). AVAILABLE COOKTOP SETTINGS - Your control provides different settings for each heating zone. Some of these power levels include Keep Warm (Fig. 4), Lo (Fig. 5), Med (Fig. 6), Hi (Fig. 7) and OFF position (Fig.8). Fig. 4 medmed med Fig. 6 Fig. 7 Fig. 8 THE RECOMMENDED SURFACE COOKING SETTINGS Use the chart to determine the correct setting for the type of food you are preparing. 8 14 13 12 11 10 9 15 Recommended Surface Settings Table Setting Type of Cooking HIGH (15) MEDIUM HIGH (11-14) MEDIUM (7) MEDIUM LOW (3-6) LOW (1) Start most foods; bring water to a boil and pan broiling. Continue a rapid boil; frying, deep fat frying. Maintain a slow boil; thicken sauces and gravies; steaming vegetables. Keep foods cooking; poaching and stewing. Keep warm, melting and simmering. Note: The size and type of cookware used will influence the setting needed for best cooking results. 13Setting Surface Controls OPERATING THE SINGLE SURFACE RADIANT ELEMENTS !CACACACACAUTIONUTIONUTIONUTIONUTION Radiant surface elements may appear to have cooled after they have been turned OFF. The Hot Surface Indicator Light will turn ON and will continue to glow until the glass cooktop has cooled down to a moderate level. The glass surface may still be hot and burns may occur if the glass surface is touched before the indicator light has turned OFF. Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements. The cooktop has single radiant surface elements at 2 locations; the right and left rear (Figs. 1 & 2) element positions. To Operate the Single Surface Element 1. Place correctly sized cookware on the radiant surface element. 2. Touch and hold the POWER key pad until a beep sound. The power indicator light above the POWER will turn ON. Note: If no other key pad is touched within 20 seconds the request to Power ON the cooktop will clear. 3. Touch and hold the ON OFF pad for the desired element position until a beep is heard. The indicator light...