Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3). The two slide switches are for the various fan functions: one is for the fan speed and the other is for the hob light. The button with the “ ” symbol is used to adjust the fan speed or intensity. It is advisable to use low speeds when cooking food that produces an average amount of steam and odour; the more steam and odour there is, the higher the speed should be. The button with the “ ” symbol is for switching on and off the hob light. Moreover, the fan hood is equipped with a micro-switch which can be found under the lower runner of the pull-out panel on the right hand-side. With this micro-switch, the appliance may be automatically switched on and off by opening and closing the pull-out panel, but only if the fan speed has already been set and the light button is turned to “I”. Care and Maintenance Always turn off the appliance before carrying out any repair or maintenance work. For safety reasons, unplug at the wall socket. Grease filterThe purpose of the grease filter is to collect grease particles which form during cooking and it should always be used, either in the extraction or recirculation mode. You should take out my grease filters every four weeks and wash them either in the dishwasher or by hand. To remove the filter, proceed as follows: a) remove the grid; b) take out the dirty filter pushing on the locking devices Z (figure 2); c) Wash the filters in the dishwasher or by hand. 2 Z Soak grease filters for about one hour in hot water with a grease- loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Place grease filters in dish washer. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. Whenever the filters are washed, clean the grid with warm water and a non-abrasive liquid detergent. Hand washing Dishwasher machine 11 Active carbon filter Cleaning Replacing the lamps This filter is used when the hood functions for internal recycling. The original AEG active carbon filter should be used (see Special accessories). It is neither washable nor reusable. In normal cooking conditions, we recommend that it be replaced every 4 months. To replace the active carbon filter, push the locking tabs E inwards and the filter downwards (see diagram on pag. 4). When ordering a new active carbon filter, indicate the model description and fan hood serial number. This information can be found on the rating plate inside the appliance. Filters can be ordered at any AEG retailer. Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grille. Wash the outside surfaces using a mild detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and mild detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Always turn off the electricity before replacing lamps: 1) Remove the grid in order to check the lamps and replace them if necessary. 2) Unscrew the lamps that do not work and replace them with 40W max lamps (E14). If the light does not function, check that the lamps are properly screwed-in before contacting the AEG Service Dept. Attention Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. 12 Technic details Weight: 335 D Net: 10,8 Kg Maximum connected watt: 230 W Motor absorption: 150 W Lighting: 2 x 40 W (E14) Length of the cable: 165 cm Extraction rate according to DIN 44971 Min. Max. Extractor: 147 m3/h 297 m3/h Recirculating: 97 m3/h 202 m3/h Special accessories Wall box (O 120 mm) E-Nr. 647 000 016 Wall box (O 120 mm) 647 000 020 120 mm outlet hose 647 000 012 100 mm outlet hose 647 000 010 KLF60/80 activated carbon filter 610 899 421 Technical assistance service In case of any enquiries and faults, please call AEG After-Sales Service: AEG Domestic Appliances Limited Head Office: 217 Bath Road Slough, Berks SL1 4AW Tel: 01753 872506 Telefax: 01753 512271 AEG Northern Service Centre: AEG Scottish Service Centre: Unit 20, Haigh Park Block 11, Unit 1 Haigh Avenue Dundyvan Industrial Estate Stockport Coatbridge GL Manchester SK4 1QR Lanarkshire ML5 4AQ Tel: 0161 487 2205 Tel: 01236 440387 Telefax: 0161 474 1191 Telefax: 01236 440256 Service Appointments Bristol: 01179 252880 Norfolk: 01603 765515 When calling please state the following 1. The model number 2. The E-No. 3. The F-No. The manufacturer reserves the right to make alterations in design and colour in the interests of technical development without prior notice. AEG Hausgerate AG Postfach 1036 D-90327 Nurnberg © Copyright by AEG H 260 287 040 L...