Stimmen - 6, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Do not use the receptacle and CALL your electrician. 19. Check that neither the appliance nor the power cable have been damaged in any way during transportation. 20. Before connecting to electric power outlet, check your electrical power supply. It must be 120 volts A.C. (alternating current). The outlet may be 15 amp. or 20 amp. The circuit must be of adequate size and must be protected by fuse or circuit breacker. DO NOT place heater directly beneath electrical receptacle and DO NOT place heater against paper board or low density fiberboard. DO NOT touch hot surfaces. DO NOT immerse cord, plug or heater in water or othet liquid, or pour this will cause dangerous electrical conditions and potential electrical shock. DO NOT obstruct the top or bottom air openings. Dust and lint on the heating element can obstruct the free flow of air. DO NOT operate when so obstructed. Operating with air openings obstructed could cause a dangerous condition. 22. Make sure that no pieces of polystyrene or other packaging material have been left into the appliance. It may be necessary to pass over the appliance with a wacuum cleaner. 23. When switching on the appliance for the first time, allow it to run at full power for about 1 hours to get rid of the unpleasant smell. Make sure that the room in which the appliance is located is well ventilated during this operation. 24. It is not advisable for the appliance to be positioned where it is exposed to draughts which might prevent it from working properly. SAVE THESE INSTRUCTIONS HOW TO USE YOUR HEATER Required Tools (not included): 1 Screwdriver PH 2 x 100 (Phillips type) Estimated assembly time: 5 minutes FEET ASSEMBLING Remove the feet from the packing. Fit the feet to the appliance as follows: 1 Insert the anchor pins (A) into the slots and turn the foot until it clicks into position (fig. 1). 2 Fasten the feet in position using the screw (fig. 2). BE CAREFUL A fig. 1 fig. 2 Operate the heater in upright position only. Any other position could create hazard situation! The appliance is fitted with a tilt-swich which turns the appliance off if it should fall over. To restart the appliance, simply place it upright again. LOCATION Place heater on floor beneath coldest window in the room or any desired location. Your heater will minimize the effect of cold drafts. The heater must not be located immediately below a socket-outlet. SWITCHING HEATER ON The heater must be connected to a properly polarized A/C 120 V household outlet in perfect working conditions. Keep loose clothing or bedding, furniture and flammable material away from the wall outlet where the heater plug is fitted in. Turn the thermostat knob clockwise to the highest setting and push one or both switches on. Pilot lights will go on, indicating that unit is operating. REMINDER To completely shut unit off, both switches must be placed in "0" position (lights off). THERMOSTAT OPERATING The thermostat operates on room air temperature and not heater temperature. Counter clockwise direction - lower number, lower temperature. Clockwise direction - higher number, higher temperature. Switch your heater on as shown in the previous paragraph. When your room reaches a comfortable temperature, turn thermostat knob back gradually until you hear a "click" and not further. Keep thermostat at this temperature, the heater switches on automatically until the room again reaches the set temperature. Room comfort is thus maintained with minimum use of electricity. 0 MODEL WITH FAN Proceed as follows: -as warm ventilation during cold months, by pushing on the fan switch (see figure), along with one or both switches. Your fan will propel the heat instantly. -as cold ventilation simply turning clockwise the thermostat knob to its maximum position and without pushing on the switches, but the fan switch. Your fan will refresh room-air circulation. MAINTENANCE AND SERVICE Disconnect electric and allow the heater to cool. Wipe with a soft damp cloth, do not use detergents and abrasives. Should the heater not be in use over a certain lenght of time, keep it in a dry place. This appliance has been built to give many years of trouble free service. In case of malfunction or doubt, do not try to repair the heater yourself. Call nearest Service Centre (see attached list of Service Centers). limited warranty This warranty applies to all products with De’Longhi or Kenwood brand names. What does the warranty cover? We warrant each appliance to be free from defects in material and workmanship. Our obligation under this warranty is limited to repair at our factory or authorized service center of any defective parts or part thereof, other than parts damaged in transit. In the event of a products replacement or return, the unit must be returned transportation prepaid. The repaired or new model will be returned at the company expense. This warranty shall apply only if the appliance is used in accordance with the factory directions, which accompany it, and on...