Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Fisher & Paykel Dateigröße: 705.16 kb Dateiname: 111024C_NZAUS_Slideout_UG_07_08.pdf Unterrichtssprache:

Weight of the product is 6.5 kg. Installation instructions Thank you for purchasing a quality Fisher & Paykel rangehood. Each rangehood is tested and approved before it leaves the factory, ensuring our high standard of quality control is met. Contents of packaging 1 x rangehood 1 x installation instructions 4 x Spacer Tube 25.4 mm 4 x Screw 8x1.5” 4 x Screw 8x1” Typical equipment required: Electric drill Screwdriver Duct tape (if ducting) Jig saw (if ducting) Ladder (if ducting) Ducting Tape measure Drill bits Spirit level Accessories Fig.1 Slideout rangehood Accessory Part Number Replacement aluminium filter R103794 Charcoal filter R103794C Light bulb R111020 Installation instructions Height of rangehood Please read the entire instructions BEFORE installing the rangehood. Ascertain the desired installation height of the rangehood. When installing the rangehood, the lower edge of the unit must be a minimum of 600 mm (650 mm for gas cooker) above the cooking surface. The recommended position for the hood is 650 mm above the hotplates. Any installation above 750 mm will compromise the extraction performance. A = 600 min (electric cook top) A = 650 min (gas cook top) Not less than 650 mm Gas Burner Fig.2 Positioning Ducting options Some authorities require rangehoods to be vented outside. Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air is fulfilled. Top ducting through roof Rear ducted Side ducting Fig.3 Ducting options 285 x 85 mm rectangular, or 150 mm diameter round ducting (using a rectangular-to-round adaptor) can be used in conjunction with this model. For optimal efficiency, use smooth ducting for reduced noise and increased airflow. Flexible ducting should only be used as a last resort. Note: we recommend an Easy Fit by Fisher & Paykel or a UNIDUCT ducting system, products that have been designed to expel air efficiently. Installation instructions Preparing the rangehood for installation Ensure the overhead cabinets are built according to Fig.5 (below). Before drilling any holes, check that the area Knockouts (remove for ducted only) behind the surface to be drilled is clear of any electrical cables or pipes etc. Recirculating If the rangehood is to be installed as a recirculating hood, the knockouts shown in Fig.4 should not be removed. For recirculation please purchase a charcoal filter (R103794C). Ducting If the rangehood is to be installed as a ducted hood, remove the appropriate duct knockout. See Fig.4. Fig.4 Preparing for install 1 Remove Cover Tape ‘A’. See Fig.4. 2 If 80 mm handle is not installed. Remove Front Fascia ‘B’ by undoing 3 screws on the fascia (see Fig.4). 3 Replace ‘B’ with Replacement Front Panel ‘C’ constructed of same or similar material as cupboard doors. See Fig.5 for height of panel. Mounting the rangehood The rangehood can be mounted in two ways, top or sides. Before commencement, unpack the rangehood and check that it functions correctly. Mounting to underside of cupboard Fix rangehood to a shelf mounted at the right height in your wall units, by drilling 4 holes (see Fig.6) and fixing with 4 screws supplied. Filtered air Cooking fumes Fig.5 Panel heights Wall Cupboard Door For top ducting cut hole to suit size Dimensions shown are for UNIDUCT Drill 5 mm holes Fig.6 Mounting to underside of cabinetry Installation instructions Mounting to cabinetry sides Fix rangehood to your wall units, with 2 screws in each side into the vertical panels. To do this: 1 Slide out the drawer and remove filter. You will see two mounting holes running through the moulded sides. 2 Remove thin plastic skin (A) from each side ...

Herunterladen

Geben Sie zwei Ziffern: