Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
To learn more about MieleCare Extended Service Contracts, please contact your appliance dealer or visit us online at: Installation Instructions Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. Do not attach the plate directly to the ceiling with anchors, toggle bolts, etc. Electrical data All electrical work should be performed by a qualified electrician in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work. Ensure that power to the appliance is OFF while installation or repair work is performed. ^ Verify that the voltage, load and circuit rating information found on the data plate (located behind the grease filter), match the household electrical supply before installing the hood. If there is any question concerning the electrical connection of this appliance to your power supply, please consult a licensed electrician or contact Miele’s Technical Service Department. See back cover for contact information. WARNING: THIS APPLIANCE MUST BE GROUNDED Important The hood must be hard wired accordingly: Black/Red wire:. . . . connect to L1 (live) White wire: . . . . . connect to N (neutral) Green wire: . . connect to GND (ground) Maximum load DA 220-3. . . . . . . . . . . . . . . . . . . 430 W Lighting . . . . . . . . . . . . . . . . . .4 x 20 W Voltage . . . . . . . . . . . . . . . . . . . . . 120 V Frequency . . . . . . . . . . . . . . . . . .60 Hz Circuit rating. . . . . . . . . . . . . . . . . . 15 A Appliance dimensions a Mounting bolt holes b Alternative positions to feed through the power cord c Exhaust connection 6" (150 mm) diameter Installation Do not install this exhaust hood over cooktops burning solid fuel. Provided a larger distance is not given by the manufacturer of the cooktop, follow the minimum safety distances between a cooktop and the bottom of the hood: - 22" (550 mm) above electric cooktops, - 30" (762 mm) above gas cooktops, - 26" (650 mm) above an open electric grill or open electric boiler/fryer. If there is more than one appliance beneath the hood and they have different minimum safety distances always select the greater distance. Observe local building codes. See "Important Safety Instructions" for further information. CAUTION: During the installation process, please be careful of sharp edges that can cause harm. Installation accessories 4 Screws 8 x 60 mm with 4 Washers (S10 wall anchors included in the packaging are not for use in USA/CDN.) 2 spring clips to hang the hood onto the mounting plate 4 Flat head screws M 6 x 20 mm with nose and 4 M 6 locking nuts for securing the motor assembly 1 hose clip for securing the ducting Installation ^Cut a 7 ." (190 mm) hole in the ceiling centered over the cooktop for the exhaust duct to pass through. The exhaust connection has a 6" (150 mm) diameter. ^ Hold the mounting plate up to the ceiling so that the orange arrow faces the front of the hood and aligns with the line drawn on the ceiling. ^ Mark the position of the four mounting bolts, a, for securing the mounting plate. ^ Determine the position of the hole the power cord, b, will pass through. Select the hole providing the shortest route for the power cable, b, to reach the power terminal located at the top of the hood’s chimney. ^ Feed the ductwork and power cable through their respective holes in the ceiling. Installation If 6" (150 mm) ductwork is not possible then 5" (125 mm) ductwork can be used in conjunction with a reducing collar available from the Miele Technical Service Department (see "Installation / Air extraction" for further details). ^ Drill four 3/16" (5 mm) holes in the ceiling. ^ Secure the ducting to the mounting plate using a hose clip. The S10 wall anchors included in the packaging are not for use in USA/CDN. Be certain that the ceiling is stable enough to support the hood. Installation ^ Screw the mounting plate through the ceiling and into the structural framing using 8 x 60 screws and washers. Once tight, make sure that the ^ Insert the short edge of the two spring clips into their slots from below and pivot them 90° so that the tab faces the center of the mounting plate. mounting plate can safely support the weight of the hood. ^ Pull the power cord through the mounting plate. ^ Insert the four flat head screws M 6 x 20 into the recessed holes from above. ^ Tape the screws from above to prevent them from being pushed upwards when the nuts are tightened. Installation ^ Using at least two people, lift the hood and guide the spring clips through their respective slots in the flange at the top of the chimney. Make sure they click into place and that the hood is hanging securely from the spring clips before al...