Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Xpelair, modell PW482718R

Hersteller: Xpelair
Dateigröße: 213.5 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

HEAT LAMPS Wolf Pro 27" (686) deep wall hoods are equipped with two heat lamp locations that require R40, 250W maximum bulbs. Heat lamp bulbs are not included with the hood. To replace, turn off the ventilation hood blower and lights. Once the heat lamp bulb is cool, use a soft cloth to unscrew the bulb and replace. Be sure that the heat lamp bulb is cool before touching. Dimensions in parentheses are in millimeters unless otherwise specified. WOLF PRO VENTILATION HOOD USE & CARE SIGNATURE POLISH Signature Polish is available from Signature Limited Laboratory, P.O. Box 13436, Dayton, Ohio 45413-0436, or call 877-376-5474 (toll free). CLEANING AND CARE Most surfaces of your Wolf Pro hood are stainless steel. Although resistant to most stains, it is not totally impervious to damage. GENERAL CLEANING Salt and some cooking liquids may pit and stain the surface. Always remove any film or spills immediately. Avoid using abrasive cleaners. They will permanently scratch the surface. Do not use steel wool pads. Be careful not to soak the rotary switches. Although they are sealed, excessive moisture may cause damage to the controls. A spray degreaser will remove fingerprints and greasy spatters. Spray on a cloth and wipe surface. Buff dry immediately to avoid streaking. Use white vinegar and water to remove hard water stains. Use a clean cloth or sponge, wipe with warm water and mild detergent. Rinse and dry immediately. Apply a protective polish like Signature Polish (see side note) to the surface to maintain luster and protect against food stains. Apply the polish following the same grain direction as the finish. DECORATIVE RAIL Clean the decorative hood rail using warm soapy water. Then hand dry with a clean, soft cloth. It is not necessary to remove the decorative rail from the hood assembly. It should be cleaned in place. Be careful not to pull or hang on the bar, as this could damage the hood assembly. STAINLESS STEEL FINISH Use a soft, nonabrasive stainless steel cleaner like Signature Polish (see side note) and apply with a soft lint-free cloth. To bring out the natural luster, lightly wipe the surface with a water-dampened microfiber cloth, followed with a dry microfiber cloth. All work should follow the same grain direction as the finish. Best results are obtained by keeping the cloth in continuous contact with the metal. Under no circumstances should you use a metallic or highly abrasive cleaner or cloth, as this will damage the finish. WOLF PRO VENTILATION HOOD USE & CARE CLEANING AND CARE FILTERS AND GREASE CUPS The stainless steel baffle filters and grease cups (if applicable) should be cleaned approximately every month, depending on use. You may need to clean the filters more often if your cooking style generates large amounts of grease (for example, frying or wok cooking). The filters are dishwasher safe and are designed to fit most dishwashers. Wolf recommends wiping filters and grease cups to remove any excess grease before placing in the dishwasher. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE SOLUTION Motor and lights do not operate A fuse in your home may be blown or the circuit breaker tripped. Replace the fuse or reset the circuit breaker. Electrical connections at the electrical box may be made incorrectly. Contact your installer. Motor runs but lights The bulb may have burned out. will not operate Switch operation may be faulty. For filter removal and reinstallation, refer to page 14. Motor does not function, but lights Check to ensure blower is plugged into hood receptacle. are operational Connect motor directly to a supply cord, bypassing hood. If the motor runs, contact a Wolf authorized service center to check switch operation and wiring between hood and blower. Excessive fan speed and/or noise Check to ensure blower wheel is not hitting side of blower. Adjust if necessary. Check blower mounting hardware. Tighten if necessary. Check for obstructions in damper flap and ductwork. Check for excessive length of duct run, number of transitions and elbows, and duct diameter. Low fan speed adjustment may be needed. Dimensions in parentheses are in millimeters unless otherwise specified. WOLF SERVICE INFORMATION CONTACT INFORMATION Wolf Customer Service: 800-332-9513 Website: wolfappliance.com SERVICE INFORMATION When requesting information, literature, replacement parts or service, always refer to the model and serial number of your ventilation hood. This information is found on the product rating plate located inside the left wall of the hood shell. Refer to the illustration for your specific model on pages 8–13 for the location of the rating plate. Record the rating plate information below fo...