Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Marley Engineered Products Dateigröße: 278.58 kb Dateiname: qmark_3038r3638r2438.pdf Unterrichtssprache:

(Fig. 10.) Install grommet in bracket (Fig. 10) and attach on each end of fan, using two of the short screws provided. Position fan over opening so that grommets are resting against center joist. Attach fan and brackets to center joist with the two long wood screws and flat washers. Do not crush grommet when tightening screws. FIG. 10 FIG. 11 GROMMET BRACKET GASKET STEP 6 - Attach side panels to fan as shown using remaining short screws and washers. (See Fig. 11.) Bottom panels should rest upon ceiling. Bend flaps on ends of panels back when inserting panels between joists. These flaps will then spring back to seal off any space between panel and joist. 5 SHUTTER INSTALLATION STEP 7 -Unpack Model A3024 shutter and read instructions included. Note that the first part of the shutter instructions refer to cutting the shutter hole, which you have already done, and so they may be disregarded. Follow the remaining instructions to adjust springs so that shutters open and close freely. (See Fig. 12.) FIG. 12 SPRING ATTACHED SPRING HOLDERCONNECTOR SPRING SHOWN UNATTACHED LOCKING SCREW STEP 8 -Mount shutter to joists directly below fan opening with wood screws provided. Note sheet rock must be covering center joist before shutter is installed. Again, make sure both sides of shutter open and close freely. (See Fig. 13.) Also make sure there is clearance between spring holder on shutter and fan blade. FIG. 13 STEP 9 -Fan installation is not complete. Follow wiring instructions on pages 11 and 12. Test-run fan through all speeds. 6 CEILING INSTALLATION — ALL OTHER MODELS FAN LOCATION & MOUNTING STEP 1 - Fan should be located in center of house, preferably in hallway or corridor. This will allow air to Fan should be located in center of house, preferably in hallway or corridor. This will allow air to be drawn from all parts of living space. (See Fig. 1.) FIG. 1 FIG. 2 FAN OVERLAP AREA PILOT HOLE STEP 2 - Lightly mark a square opening on ceiling (with pencil) where shutter is to be located. Select opening size from chart below on Page 1. Check to be sure at least 1 1/2 inches of clearance area is available on all sides for overlap of shutter flanges. (See Fig. 2.) Drill a small pilot hole in the center of this square through ceiling. STEP 3 - Determine ceiling joist size and spacing; the most common types are: 2 x 4 on 16” centers 2 x 6 on 16” centers 2 x 4 on 24” centers 2 x 6 on 24” centers Now find pilot hole in attic, and tentatively lay out same square hole as on ceiling below. Adjust location of this hole so as to cut as few ceiling joists as possible and to ensure a minimum vertical clearance from roof rafters of 18” above fan. (See Fig. 3.) See installation drawings and specific instructions for your ceiling configuration on page 8, 9 & 10. To make cuts through joists, use either a saber saw or circular saw. Carefully finish cut with hand saw or chisel, so that ceiling below is not damaged. (See Fig. 4.) FIG. 3 FIG. 4 18” MIN. CLEARANCE ROOF RAFTERS 7 MODEL 2438 FOR CEILINGS WITH 2 X 4 JOISTS ON 16” CENTERS FIG. 5 Determine which ceiling joists are to be cut per STEPS 2 & 3. Locate your fan size below and follow specific instructions. MODEL 3038R WITH MODEL 3230 SHUTTER Cut ceiling joists to allow 2 x 6 frame box with 24 3/4” x 24 3/4” inside opening. MODEL 3638R Cut ceiling joists (as shown) to allow 2 x 6 frame box with 30 3/4” x 30 3/4” inside opening. Add 2 x 2 filler to each side. Proceed to STEP 4. Cut ceiling joists to allow 2 x 6 frame box with 36 3/4” x 36 3/4” inside opening. FOR CEILINGS WITH 2 X 6 MODEL 2438 JOISTS ON 16” CENTERS 2 X 6 Determine which ceiling joists are to be cut per STEPS 2 & 3. Locate your fan size below and follow specific instructions. MODEL 3038R WITH MODEL 3230 SHUTTER Cut ceiling joists to allow 2 x 6 frame box with 24 Cut ceiling joists to allow 2 x 6 frame box with 36 3/4” x 36 3/4” inside opening. 2 X 6 FRAMING FIG. 6 2 X 6 FRAMING 2 X 2 FILLER FIG. 7 2 X 6 FRAMING FIG. 8 FRAMING 3/4” x 24 3/4” inside opening. FIG. 9 2 X 6 FRAMING Cut ceiling joists to allow 2 x 6 frame box with 30 3/4” x 30 3/4” inside opening. FIG. 10 MODEL 3638R 2 X 6 FRAMING Proceed to STEP 4. 8 FOR CEILINGS WITH 2 X 4 JOISTS ON 24” CENTERS Determine which ceiling joists are to be cut per STEPS 2 & 3. Locate your fan size below and follow specific instructions. Frame inside opening per chart below. FAN MODEL FIG. 11 2 X 6 FRAMING INSIDE OPENING 2438 24 3/4” X 24 3/4” 3038R* 30 3/4” X 30 3/4” 3638R 36 3/4” X 36 3/4” Proceed to STEP 4. FOR CEILINGS WITH 2 X 6 JOISTS ON 24” CENTERS Determine which ceiling joists are to be cut per STEPS 2 & 3. Locate your fan size below and follow specific instructions. Frame inside opening per chart below. FIG. 12 FRAMING2 X 6 FAN MODEL INSIDE OPENING 2438 24 3/4” X 24 3/4” 3038R* 30 3/4” X 30 3/4” 3638R 36 3/4” X 36 3/4” Proceed to STEP 4. STEP 4 - Now carefully cut hole in ceiling flush with inside of frame. STEP5 - Attach gasket to bottom of fan frame. Be sure gasket sea...

Herunterladen

Geben Sie zwei Ziffern: