Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Universal Metal Industries Dateigröße: 99.36 kb Dateiname: Unterrichtssprache:

Charcoal filters will not remove odors if washed and should be replaced periodically—every few months depending on usage. Replacement filters are available from the manufacturer. Please call 800-875-3654. CONNECTING TO THE VENT PIPE: The hood is equipped with a metal damper. Attach the damper to the hood top or back side of the hood with at least two screws. Duct tape the edges to the hood. Be careful to not damage or tape over the damper blade. When connected to the back of the hood (horziontal ventilation), be sure the damper swings open from the bottom side; the hinge will be on the top. Otherwise, it will NOT close when the motor is off. Item No. 0AL00-UL-001 Revised 02/02/06 Copyright (C) 2006, Universal Metal Industries, Inc. Page 5 PART 4 Use and Care OPERATING CONTROLS: Always activate the ventilator when using cooking appliances. Activate the ventilator a few minutes before starting to cook to establish an airflow pattern within the room. Adjust the fan speed as needed. Adjust the dimmable halogen lights as desired. Eliminate air currents in the hood vicinity by shutting nearby windows and doors, turning off ceiling fans and adjusting the adjacent heating and air conditioning outlets if necessary. Place your largest pans on the rear burners whenever possible. WARNING! Do NOT operate the blower / ventilator system without the filters in place, or with dirty, grease laden filters. ENERGY SAVING TIPS: Do not operate the blower at a speed higher than necessary to remove the cooking exhaust. Running at excessive speeds removes more air from the inside of the house that must be replaced by outside air. This may be especially costly when your home’s heating or air conditioning system is in operation. Turn off the unit once the smoke and cooking odors have been eliminated. Clean filters and grease laden surfaces often to improve efficiency. Always use lids on cookware to retain heat and moisture. Minimize the amount of liquid used to cook food. Select cookware of proper size, material and construction for the cooking task being performed. CARE & CLEANING: Proper cleaning is necessary to maintain performance and appearance, while also ensuring safe operation. The frequency of cleaning should be adjusted according to the type and amount of cooking. Best results will be achieved by cleaning soiled components as soon as possible. Filters must be cleaned regularly. Remove one filter at a time by inserting a butter knife in the slot and pressing back then downwards. Butter knife filter slots are a safety feature. The filter should be installed with the butter knife slot on the front lower side. The filters may be cleaned by hand washing in hot water using a mild detergent solution, or by placing them in a dishwasher. Dry the filters completely before using again. Stainless steel surfaces should be cleaned with a solution of mild detergent and warm water. Rinse and dry with a soft lint-free cloth. Charcoal filters are ineffective if washed and should be replaced periodically. Contact your dealer or Universal Metal Industries for replacement. CAUTION: If a commercially available stainless steel cleaner is used, it is important to read the labels for chlorine compounds. Chlorine is a corrosive substance. If these compounds are present, rinse thoroughly and dry with a soft lint-free cloth. Follow polish manufacturer’s instructions. Always wipe stainless steel surfaces with the grain. Never wipe across the grain. After cleaning, reinstall the filters carefully. Most common scrubber type pads will scratch the hood. HALOGEN LIGHT BULBS: Hoods are designed for PAR 20 halogen lamps. They can be purchased at most home and/or grocery stores, e.g., McCoys, Lowe’s, Fry’s, Kroger, Albertsons, True Value, Home Depot, etc. Universal Metal Industries, Inc. has a policy of continuous improvements and reserves the right to modify (at any time, without notice) any or all of its products, features, designs, components and specifications. For exact dimensions, see the installation instructions included with each product. Some features may be slightly different than shown on product literature. For questions regarding this product contact: Customer Service Universal Metal Industries, Inc. P.O. Box 2409 Phoenix, AZ 85002 (602) 251-3654 umiphx.com customrangehoods.com artechusa.net Item No. 0AL00-UL-001 Revised 02/02/06 Copyright (C) 2006, Universal Metal Industries, Inc. Page 6 ...

Herunterladen

Geben Sie zwei Ziffern: