Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Whirlpool Dateigröße: 432.64 kb Dateiname: Unterrichtssprache:

Round vent only: Replace round vent plate removed in step 1 of “Prepare the Hood” section. Install a 7" (17.8 cm) round damper (must be purchased separately). The damper flap must open freely in the direction of air flow (away from range hood). NOTE: Damper/vent connector and round vent plate can be installed up to 1" (2.5 cm) on either side of hood center if ventwork is off-center. In extreme off-center installations, one end of the vent connector may need to be trimmed to clear the electrical strain relief. Make Electrical Connection Direct Wiring Installation 1. Disconnect power. 2. If not previously done, run wiring through wall or cabinets according to electrical codes and ordinances. 3. Stand hood up as shown. (Keep on protective cover to protect hood and cooking surface.) Feed the power supply cable through the strain relief. 4. Use twist-on connectors and connect black wires together. 5. Use twist-on connectors and connect white wires together. WARNING Electrical Shock Hazard Electrically ground the blower. Connect ground wire to green ground screw in wiring box. Failure to do so can result in death or electrical shock. C B A A. Semi-circular knockout B. Top rectangular knockout C. Rear rectangular knockout B A B C C Vertical vent position Horizontal vent position A. Up to 1” (2.5 cm) side-to-side adjustment B. Pivot C. Damper/vent connector WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 6. Connect the power supply ground wire to the green ground connector and tighten securely. A. Green ground connector A 7. Securely tighten the strain relief. 8. Replace the wiring cover. UL-Listed Power Supply Cord Kit (U.S. Only) 1. Connect a UL-listed Power Cord Kit (part no. 99524057) (U.S. only) following the kit instructions for connecting the wires. 2. Replace the wiring cover. Install Range Hood WARNINGExcessive Weight Hazard Use two or more people to move and install range hood. Failure to do so can result in back or other injury. 1. Remove the 4 hood mounting screws from the parts bag and install in previously drilled ..." (3.0 mm) pilot holes. Leave screw heads about ..." (6.4 mm) away from shim strips. ..." (6.4 mm) 2. Lift range hood into final position, feeding electrical wire through wiring opening. To avoid damage, do not push on fan blade. 3. Position the range hood so that the large end of the keyhole slots are over the screws. Then push the hood toward the wall so that the screws are in the neck of the slots. B A A A. Keyhole slots (4) B. Mounting screw 4. Tighten mounting screws to cabinet, making sure mounting screws are in narrow neck of slots. On vented installations: 5. Make sure that damper blade opens and closes freely. 6. Connect ventwork to hood. Seal joints with duct tape to make them secure and air tight. Complete Installation 1. Install (2) PAR20, 50W maximum halogen bulbs or (2) R16, 40W maximum incandescent bulbs. Bulbs purchased separately. 2. Replace filters. NOTE: Filter slot must be toward front of hood. For non-vented installations: Attach the charcoal filters (not supplied) to the aluminum filters with the special blue and yellow strips facing toward the cooking surface. Make sure fan blade turns freely. 3. Reconnect power. 4. Check for proper operation. RANGE HOOD USE Operation Hood control panel LOW HIGH FAN LOW HIGHLIGHT A B A. Fan switch B. Light switch Operating the fan A 3-position rocker switch controls the fan. The left position is low speed, center position is off, and the right position is high speed. An indicator light shows that the fan is on. Operating the light A 3-position rocker switch controls the lights. The left position is low light intensity, center position is off, and the right position is high light intensity. Replacing the light bulbs Before you begin, make sure that the range hood is turned off and that the lamps have had sufficient time to cool. Halogen bulbs burn extremely hot. See bulb packaging for further information. Replace with (2) PAR20, 50W maximum halogen bulbs or (2) R16, 40W maximum incandescent bulbs. RANGE HOOD CARE Cleaning and Maintenance Be sure lights are cool before cleaning the hood. To clean hood 1. Disconnect power. 2. Remove filters. 3. Use a damp cloth and a mild detergent to wipe all grease- laden surfaces. Use care when cleaning fan blade - it must not become bent or misaligned. Do not allow water to enter the motor. 4. Make sure all surfaces are completely dry before replacing filters. 5. Reconnect power. Motor is permanently lubricated. Do not oil or disassemble motor. Aluminum mesh filters Clean often using hot water and a mild detergent. Filters are dishwasher safe. Charcoal filters (non-vented installations) ¦ Clean filter surfaces frequently with a damp cloth and mild detergent. Do not immerse filters in water or put in dishwasher. ¦ Special blue and yellow strips will blend to green when it is ti...

Herunterladen

Geben Sie zwei Ziffern: