Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following: 1. Read all instructions before installing or using accidentally. When the service disconnecting means exhaust fan. cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 2. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the 4. Installation work and electrical wiring must be done manufacturer. by qualified person(s) in accordance with all applicable codes and standards, including fire-related construction. 3. Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting 5. Sufficient air is needed for proper combustion and means to prevent power from being switched on exhausting of gases through the flue (chimney) of SAVE THESE INSTRUCTIONS 210572111 Rev. B 5-06 1 of 8 GENERAL SAFETY INFORMATION (Continued) fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local code authorities. CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS. 6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 7. Ducted fans must always be vented to the outdoors. 8. This unit must be grounded. 9. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. WARNING: DO NOT INSTALL OVER A TUB OR MOUNT IN A SHOWER STALL ENCLOSURE. 10. Do not install into a ceiling thermally insulated to a value greater than R-40. 11. NEVER place a switch where it can be reached from a tub or shower. WARNING: DO NOT USE IN KITCHENS WARNING: THIS UNIT IS DESIGNED AND TESTED TO BE A SUPPLEMENTAL HEATER FOR USE WITH A TIMER OR A SWITCH. IT IS NOT INTENDED TO BE USED AS THE PRIMARY SOURCE OF HEAT AND CONTROLLED BY A THERMOSTAT. INSTALLATION INSTRUCTIONS CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. SECTION 1 Preparing the Unit 1. Unpack fan from the carton and confirm that all pieces are present. In addition to the unit you should have: 1 - Grill with Light Lens 4 - Mounting Rails 1 - Instruction/Safety Sheet 2. Remove the two machine screws holding the light reflector in place. Keep the reflector and screws in the carton until needed so they do not get damaged or lost. (Figure 1). Figure 1 Screws 3. Remove the wire compartment cover by loosening the two screws holding the cover in place (Figure 2) Figure 2 Screws Wire Compartment Cover WARNING: DO NOT INSTALL OVER A TUB OR MOUNT IN A SHOWER STALL ENCLOSURE. 4. Choose the location for your unit. To ensure the best air and sound performance, it is recommended that the length of ducting and the number of elbows be kept to a minimum, and that insulated hard ducting be used. Larger duct sizes will reduce noise and airflow restrictions. This fan will require at least 7" of clearance in the ceiling, and will mount through drywall up to 3/4" thick. The fan can be mounted directly to the joist using the mounting tabs on the side of the housing or between 16" on center joists using the 4 provided mounting rails. 5. Remove the electrical knockouts using a straight- blade screw driver (Figure 3). SECTION 2 New Construction Figure 3 1. Mounting Rail Installation: Install the rails on the housing and position the housing next to the joist. Line up housing so it will be flush with the finished 210572111 Rev. B 5-06 2 of 8 ceiling. Secure the ends of the rails with screws or nails (not included) to the joists and slide housing into final position (Figure 4). Figure 4 Joist Housing Mounting Rails 1a. Mounting Tab Installation: Line up housing so that it will be flush with the finished ceiling. Position the fan so that the tabs rest flat against the joist and secure with screws or nails (not provided) to ensure proper installation (Figure 5). Figure 5 SECTION 3 Existing Construction 1. Mounting Rail Installation: Set housing in position between the joist and trace an outline onto the ceiling material (Figure 6). Set housing aside and cut opening, being careful not to cut or damage any electrical or other hidden utilities. Install the rails on the housing and position the housing in t...
Dieses Handbuch ist für folgende Modelle:Ventilatoren - BFLH85L (158.7 kb)