Stimmen - 4, Durchschnittliche Bewertung: 5 ( )

Hersteller: Dacor Dateigröße: 705.9 kb Dateiname: Unterrichtssprache:

Do not install a damaged or incomplete appliance. Hood assembly with filter(s) Chimney assembly (2 piece) Mounting bracket Blower exhaust cowling (2 blower units only) Framework assembly (2 piece) Mounting and assembly hardware Use and care manual Make sure you have everything necessary for proper installation before proceeding. A B C D E F G A B C D E F G preparing for insTallaTion preparing for insTallaTion WARNING • • • • The electrical service to the range hood should be installed only by a licensed electrician. Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. DO NOT use the mounting anchors provided with the unit. They are part of a standard mounting hardware package provided with many Dacor hoods, but not suitable for use with this model. The range hood is heavy. To prevent personal injury and property damage caused by the hood coming loose from the ceiling, mount the hood mounting bracket only as specified below. planninG the location • Carefully check the location where the hood is to be installed. The hood should be placed for convenient access. Make certain that electrical power can be provided in the selected location. • Install the range hood and cooking appliance(s) so that they can be removed if service is required. • Plan the installation so that all minimum dimensions are met or exceeded (see page 3). Dimensions shown provide minimum clearances, unless otherwise noted. Preparing the Mounting Bracket Location • The mounting bracket must be attached directly to the studs in the ceiling, or to a reinforced mounting block secured to the studs. See below for mounting bracket hole dimensions. 129/16” (31.9cm) 61/8” (15.6cm) 11” (27.9cm) • Attach the mounting bracket directly above the center of the cooktop. • Attach the mounting bracket to the mounting surfaces with #12 screws (not supplied). The screws must be of sufficient length to penetrate into the wood mounting surfaces at least 1 1/2” (3.8 cm). • The mounting surface must be level. • Allow clearance in the center of the mounting bracket for the exhaust duct to pass through the ceiling (8-inches in diameter). electrical power Supply Electrical Specifications It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician. The electrical installation, including minimum supply wire size and grounding, must be in accordance with the National Electric code ANSI/NFPA* (or latest revision) and local codes and ordinances. Connect the hood to a 120 Vac, 60 Hz dedicated, grounded, circuit protected by a 15 Amp circuit breaker or time delay fuse. *A copy of this standard may be obtained from: National Fire Protection Association 1 Batterymarch Park Quincy, Massachusetts 02269-9101 preparing for insTallaTion preparing for insTallaTion plan the Duct work inStallation WARNING • • • • • • To reduce the risk of fire and to properly exhaust air, be sure to duct air outside the house or building. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages. Tape all duct joints securely to prevent combustion by-products, smoke or odors from entering the home. Doing so will also improve system efficiency. Do not exhaust more than one vent into a single duct. Use only duct work constructed of materials deemed acceptable by state, municipal and local codes. Range hoods may interrupt the proper flow of smoke and combustion gases from furnaces, gas water heaters and fireplaces. To avoid drawing lethal gases into the home, follow the manufactures recommendation for these devices and consult NFPA and ASHRAE recommendations. DO NOT install an additional in-line or external blower to increase the length of the duct run. Even small differences between blower air flow rates can greatly reduce the air draw by the hood. • All duct work materials (including screws and duct tape) must be purchased separately by the customer. When planning new duct work, always look for the shortest, most direct route to the outside. • The hood exhaust connects to an 8-inch round duct. You can increase the duct size over the duct run if desired. To prevent a back draft, never decrease the duct size over the run. • Do not rely on duct tape alone to seal duct joints. Fasten all connections with sheet metal screws and tape all joints with duct tape. Use sheet metal screws as require to support the duct weight. • To prevent back-drafts, a damper at the duct outlet may also be required. • Make sure duct work does not interfere with floor joists or wall studs. Calculating the Maximum Duct Run Length The maximum straight duct length for the hood is 100 feet. For each elbow and transition added to the duct work, a certain number of feet must be subtracted from the maximum straight length to compensate for wind resistance. To determine the length the duct work cannot exceed, subtract all of the equivale...

Herunterladen

Geben Sie zwei Ziffern: