Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Empire Comfort Systems Dateigröße: 205.11 kb Dateiname: Unterrichtssprache:

This system MUST BE installed before the fireplace is enclosed with finishing material. Install model VFFB-AK-36 on VFFB-36D. Install model VFFB-AK-42 on VFFB-42D. The air will be drawn into the cooling layer of the fireplace and be completely separated from the combustion casing of the vent-free fireplace. Cooler outside air will mix with room air, circulating around the firebox to reduce the heat output and bring heated, fresh air into the house to provide a more positive balance. Fig. 8. Fresh air intake kit. R-5010 7 INSTALLING AIR SYSTEM. Remove cover plate and retain the four (4) screws. Install damper assembly into the hole from the outside of the fireplace. Reinstall all four (4) screws. (See Fig. 9). Attach the cover plate behind the bottom louver with four (4) screws, provided to the support legs on the back left side of the firebox, as shown in Fig. 9. Attach the (2) screws for damper rod bracket to the bottom of the hearth pan, while holding the damper rod bracket with the flange facing the rear of the unit. Connect damper assembly to termination using 6” diameter duct. Insulated duct is recommended when ducting through a heated space. OUTER CASING REMOVE COVER PLATE Fig. 9. Fresh air intake kit installation. Fig. 10. Top view of air system installation. Fig. 11. Example of installation. CAULKING RAIN CAP WALL DUCT TERMINATION Fig. 12. Caulk and install duct termination. 8 R-5010 C-7. INSTALLING THE HOOD. A black hood is furnished with each model VFFB36/42D fireplace and MUST be installed before the fireplace is used. Failure to do so may create a possible fire hazard. If brass hoods are desired, they can be purchased as an option. Attachment is the same, as our standard black hood. 1. Remove the one top screw and one from each side of the fireplace surround. Be careful not to remove the screen rod from the fireplace, during this procedure. 2. Line up the holes with holes in hood being installed. Insert screws and tighten securely. EXTENDED HOODS. If your facing material over 1" in thickness is used to finish this fireplace, you must purchase a different hood that will extend out 2" farther into the room. Follow steps 1 and 2 above for installation. Contact your local dealer for details. Model: VFFBH-36BR-4 – BRASS 36" VFFBH-36BK-4 – BLACK 36" VFFBH-36BP-4 – BLACK PORCELAIN 36" VFFBH-42BR-4 – BRASS 42" VFFBH-42BK-4 – BLACK 42" VFFBH-42BP-4 – BLACK PORCELAIN 42" C-8. FINISHING. All joints (top, bottom and sides), where the wall or decorative facing material meets the fireplace surround must be completely sealed with a non-combustible material. Refer to Fig. 1. Hearth extensions are recommended, not a requirement for these gas fireplaces. Do not cover the louvers at any time with finishing materials.This could cause this product to overheat and cause a fire. D INSTALLATION OF THE OPTIONAL ACCESSORIES. HOOD Fig. 13. Installation of Hood. D-1. FAN KIT. MODEL FB-BK-2 for VFFB-36D and VFFB-42D. Attention: Fan Kit, FB-BK-2 can only be used with optional louver. Open the bottom louver completely. Insert fan kit into the bottom louver. Slide the fan assembly in the left side, away from the gas line. Center this assembly in the back of the fireplace and line up the bottom bracket and the screws coming out of the bottom of the fireplace. To attach the assembly to the fireplace. See Fig. 14. Fig. 14. Fan kit installation. R-5010 9 Hold the fan kit upright so the flow from the fan BACK PANEL kit is up the back of the fireplace. Tighten wing nuts on the screws and tighten completely. Place speed control into the mounting bracket located in the right side of this fireplace behind the bottom grill. Locate the two legs over the screws coming up out of the bottom of the fireplace. Attach wing nuts and tighten completely. Plug into the junction box on the right side of fireplace. Z BRACKET D-2. INSTALLATION OF OPTIONAL SIMULATED BRICK PANELS. Remove anything within the fireplace. Install the back panel first and let it rest tight against the back wall. Place one side panel inside the fireplace and align the brick pattern. The “Z” bracket mounts along the front edge of the side panel and is held with (2) screws. Repeat the process for the other side panel. (See Fig. 15). D-3. OPTIONAL JUNCTION BOX INSTALLATION INSTRUCTIONS FBJB-1 Installation: 1. Installing the FBJB-1, junction box, should be completed during the installation of the fireplace. 2. Lower door assembly. 3. When facing the front of the appliance, the two screw holes for mounting the junction box to the interior, right side of the outer casing are adjacent to the front 1 3/4" diameter access hole. 4. Attach the junction box to the outer casing with (2) two #10 x 1/2" screws provided. 5. Install wiring to the junction box and install and wire to the plug provided. 6. Attach the cover plate. E INSTALLATION OF YOUR VENT-FREE GAS LOG SET. SIDE PANEL SCREW SIDE PANEL Fig. 15. Installation of simulated brick panels. Any vent-free Gas Log Heater must be “For u...

Herunterladen

Geben Sie zwei Ziffern: