Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Fisher & Paykel Dateigröße: 546.33 kb Dateiname: Unterrichtssprache:

3 Remove the grease filters (this is to make installation easier). Press inward on the catch, found on the handle, and pull the filter downward (Fig.4). 4 Determine location of the fixing “keyholes” on the wall. The hood is secured to the wall by two “keyholes” located above the motor behind the air exit opening. From the point where the horizontal and vertical lines drawn earlier intercept, use a spirit level and pencil and draw another horizontal line 290mm above the first horizontal line (ensuring that the line can easily be erased or the line will be hidden after installation) as shown in Fig.5. This now indicates where the top of the “fixing keyholes” are. Where the vertical line meets the top horizontal line (just drawn), measure and mark both sides of the vertical line, showing where to drill. Fig.2 Establishing height of rangehood 60 – 75 cm Rangehood centre Benchtop Bottom of rangehood Fig.3 Marking the position of the rangehood on the wall Fig.4 Removing the grease filters Installation instructions 5 Drill holes and secure the rangehood to the wall. Depending on the wall type (concrete, drywall etc) drill/screw appropriate fittings in the two locations just marked. The rangehood should now be able to be hung on these bolts/ screws through the two keyholes in the hood. 6 Create additional means of attachment. Keyholes alone are insufficient means of attachment. Drill two extra holes in the back panel, put screws in with an anchor (if required) to ensure proper attachment and fix the rangehood by these screws as well, as shown in Fig.6. Ensure all fixings are secure. 7 If ducting externally, assemble and fit ducting as per manufacturer’s instruction. 290 mm Fig.5 Determining location of the two fixing “keyholes” Optional: If desired, the one-way butterfly valve can now be fitted to the exit opening of the rangehood by simply snapping the two pieces into place. 8 Test the operation of the rangehood. Plug the rangehood in and test its operation on all speed levels. This will ensure that any imperfections holes in the installation, such as unwanted sounds or lack of suction can be addressed before the flue is in place. Over 95% of service calls are a result of faulty installation. Please be aware that in the event of a service call for a faulty installation, you will be charged as this is not covered under the manufacturer’s warranty. 9 Position and secure the flue. Secure the top mounting bracket at the highest possible point on the ceiling using a single screw through the supplied bracket. Ensure all ducting is fitted and electrical connections are secured correctly and switched on. Place the bottom part of the flue onto the rangehood and slide the upper flue piece inside the lower piece so the tabs “hug” the folded edge of the flue. Raise the upper part of the flue to the required height and, using the four screws supplied, secure the upper flue to the bracket on the wall. Installation is now complete. Keyholes Extra fitting Fig.6 Creating additional means of attachment Getting started quickly Control panel A B CDE Fig.7 Control buttons A = ALL OFF B = Low speed motor ON/OFF C = Medium speed switch ON/OFF D = High speed switch ON/OFF E = Lights ON/OFF Cleaning and maintenance Caution! Never use abrasive or oil based liquid cleaners. General maintenance The manufacturer is not liable for any damage caused by not following these instructions. The wall canopy should be cleaned regularly using warm water with soap or mild liquid detergents. This ensures that no build-up of grease occurs as these deposits are corrosive. Do not use abrasives or harsh detergents/cleaning fluids. Note: in areas of high humidity and coastal environments, cleaning should be carried out frequently. Grease deposit container Your wall canopy is fitted with a clear container located underneath the motor housing, that is only visible when the grease filters are removed. Over time, oil, fat and grease, that is normally deposited inside the motor casing, is directed into this container for easy cleaning. This unique design will help ensure your wall canopy remains in peak condition by minimising the amount of fat or grease collected in the motor. Note: This container should be cleaned as necessary, usually on an annual basis. Always ensure the container is in place prior to using the wall canopy. Do not attempt to block the hole in the motor casing. Aluminium filters The grease filters must be periodically cleaned (at least every two months). Remove the grease filters and wash them either by hand using hot soapy water or place them in the dishwasher using mild detergent. Badly smoked filters may be cleaned with “cookware cleaners”. Note: some discolouration of the frame may occur. Charcoal filters Charcoal filters are designed to remove grease and odours from cooking vapours, prior to the cleansed air re-entering the kitchen (when the wall canopy is in recirculating mode). Charcoal filters are disposable items and it is recommended ...

Herunterladen

Geben Sie zwei Ziffern: