Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
28 . 34 . ). .&#-/"# . . . Cabinet Door . . . !#-%#&'#- Figure 3 Figure 4 Bottom of the cabinet Backside of the cabinet Backside border cutout for 1/2" Conduit and 5" Duct Blind hole (Side Springs Housing) Fixing point 1-2 Fixing point 1-2 Cabinet Door Template Template Figure 5 Prepare the cabinet for installation • Mark and cut-out the cabinet bottom as shown in figure 3. • Fit the template, which comes with the hood, on the inner right side of the cabinet making sure the side with arrows matches with the lower edge of the cabinet and the rear edge of the cabinet or cut-out. • Drill 2 holes 5/64”(see figure 4 - fixing point 1 and 2) and 1 blind hole 15/” in diameter, 13/” in depth. 64 64 • Move template to the other side and repeat. • Make cut-out for duct and conduit, see figure 1. Prepare the hood for installation • Remove the hood from packaging, check its condition and make sure the following pieces are included: 1 hood, 1 registration card 1 instruction manual 1 template 1 transition with damper 1 plastic bag with 4 hood fixing screws + 1 transition fixing screw and 4 spacers. • Remove the light shield, unscrew and remove lamps to prevent damage when installing (see paragraph on “Light replacement” for details). • Pull out the slider and remove the grease filters (see paragraph “To remove the grease filters” for details). • Fit the transition on the outlet hole of the hood: This has a bayonet lock and must be fixed to the hood with one screw (Figure 5), check the opening and closing of the damper mounted inside. 4 Installation Cabinet Side Spring Figure 6 Side Spring Backside of the cabinet Fixing point 1-2 Template Figure 7 Backside border cutout for 1/2" Conduit and 5" Duct Blind hole (Side Springs Housing) Cabinet Door Bottom of the cabinet Fixing point 1-2 Template Figure 8 /%. Install the Hood • Set the motor housing into the opening. • Push the spring inside the motor housing using a screw driver as a lever from the inside of the motor housing. • Insert it completely in place taking care to snap sides springs into the blind holes made for temporary fixing and that conduit and duct section, if already fitted, run freely across the cutouts on top of the cabinet, see figure 6. • Fix the hood permanently with two screws (4.5x16) per side to be inserted frome the inside of the hood to the corresponding side fixing points 1 and 2 drilled on the cabinet, see figure 7. • Connect a 5” duct to the transition and seal with tape. • Connect to power supply Attention! While mounting the hood on the wall cabinet be sure once the hood has been fastened, that the wiring compartment is easily and safely accessible, in order to make safety inspections and/or maintenance operations. WARNING! ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU AGAINST ELECTRIC SHOCK, THE GREEN/YELLOW WIRE MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO CIRCUMSTANCES BE CUT OR REMOVED. Warning: Turn off power circuit at the service panel before wiring this unit. 120 VAC, 15 or 20 Amp circuit required. a. Remove j-box cover as shown in Figure 8. b. Remove the knockout and install the strain relief (conduit) connector (1/2") in junction box. c. Run 3 wires; black, white and green (#16 AWG) in 1/2" conduit from service panel to junction box. d. Connect black wire from service panel to black or red in junction box, white to white and green to green-yellow. See Figure 8. e. Close junction box cover. 5 Figure 8 M P Box adjustment The hood can be installed in cabinets with different depths (see also figure 1 for details); however the front of the slider box must always be flush with the front of the cabinet. For alignment, adjust the back stops of the box. For box adjustment, loosen screws M, slide the square plates P as necessary, and tighten screws M (Figure 8). Ensure that the drawer, when fully retracted, turns OFF all power by acting positively on the rear microswitch. Final installation steps • Insert lamps in place. • Fit the Lamp Shield. • Fit the Grease Filters. • Check all light bulbs to make sure they are secure in their sockets, then turn power on in service panel and check lights and blower operation per Use & Care section of this manual and install filters. • Make sure to leave this manual for the home owner. 6 READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE RANGE HOOD. Use and Care For satisfactory use of your hood, become familiar with the various functionsControl Pad Functions of the hood as described below 0 31 2 4 0 1 Air outlet Motor Housing Slider Box Left Grease Filter Handles Lamp Shield Grease Filters Blower OFF Very High Speed High Speed Medium Speed Low Speed Light OFF Light ON Right Grease Filter Handles Figure 7 Operating Instructions The blower should be turned on for about 5 minutes before cooking in order to...
Dieses Handbuch ist für folgende Modelle:Ventilatoren - B81200 Series (152.2 kb)