Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
1 pc.) Cover Plate (. 1 pc.) Duct Joint (rectangular) (Unit : inch) Dimensions (in inches) Model A B FSR-3000 30 27 FSR-3600 36 33 FSR-4200 42 39 5 1 The range hood must be installed just above the cooktop. 2 The minimum distance from the cooking surface to the bottom of the range hood must be 24”. 3 The total weight of the FSR series range hoods are: FSR-3000 ---------- 16 kg FSR-3600 ---------- 17 kg FSR-4200 ---------- 18 kg 4 Power requirements are: AC120 V, 60 Hz, 1.9 Amp RANGE HOOD LOCATION CAUTION : • Check that the hood is correctly installed, since incorrect installation could result in the detachment of the range hood and the unit fall off. • To protect hands from injury, wear working gloves when installing the range hood. RANGE HOOD LOCATION CAUTION : • Check that the hood is correctly installed, since incorrect installation could result in the detachment of the range hood and the unit fall off. • To protect hands from injury, wear working gloves when installing the range hood. 1. PREPARATION 1 This range hood can discharge upward or backward. According to the conditions where the hood is installed, determine whether it will discharge vertically (3." . 10" or 7" Round) or horizontally (3." . 10" only). For vertical or horizontal discharge, run duct work between the hood location and a roof cap or wall cap. For the best results in either directions, use a minimum number of transitions and elbows. Be sure to attach a roof cap or wall cap to avoid leaking rain in the end. 2 Use diagrams below, for proper placement of ductwork and electrical cutout in cabinet or wall. INSTALLATION WARNING: • If the range hood is not installed properly, it could become detached and fall off. • Ensure that the metal duct does not touch other metal housing materials, otherwise fire or electric shock could result. ; 3." ..... 10" Vertical Ducting INSTALLATION WARNING: • If the range hood is not installed properly, it could become detached and fall off. • Ensure that the metal duct does not touch other metal housing materials, otherwise fire or electric shock could result. ; 3." ..... 10" Vertical Ducting ; 3." ..... 10" Horizontal Ducting ; 7" Round Vertical Ducting ; 3." ..... 10" Horizontal Ducting ; 7" Round Vertical Ducting 3 Run house wiring between service panel and hood location. 4 Prepare the range hood. (1) Remove the 7" round duct joint on the top plate of the body by removing 2 fixing screws. Note: Keep the screws for reusing later. (2) Remove the Rectifier Baffle Panel by loosening the screws, and dislocating its temporary fixing holes from the screws. Note: Use a screwdriver if they are tight. (3) Remove the fan case cover by removing 4 screws. 9 7" Round Duct Joint Rectifier Baffle Panel Fan Case Cover ; In Case of 3-1/4".10" Vertical Discharge Mount the supplied 3-1/4".10" rectangular duct joint on the top plate with 4 screws (2 pieces: removed in Step 4-1, the others: supplied). Then attach the supplied soft tape around the duct joint. ; In Case of 7" Round Vertical Discharge First, remove half-cut circular part of the top plate (duct knockout) using a hammer, pliers, etc. Mount the 7" round duct joint removed in step (1) with 4 screws. Then attach the supplied soft tape around the duct joint. CAUTION: • Wear working gloves to avoid injury. • Do not apply excessive force when removing the knockout. The fan may be damaged. Duct Joint Engage with the notches Cover Plate Hit dented points on the rectangular edge Duct Knockout Soft Tape Hit dented points on the circular edge Insert into the holes Duct Knockout 7" Round Duct Joint Duct Joint Soft Tape ;In Case of 3-1/4".....10" Horizontal Discharge First, remove half-cut rectangular part of the rear plate (duct knockout) using a hammer, pliers, etc. Mount the supplied 3-1/4".10" rectangular duct joint with 2 screws. Then attach the supplied soft tape around the duct joint. To close the opening of the top plate, attach the supplied cover plate with 2 screws. ;In Case of 3-1/4".....10" Vertical Discharge Mount the supplied 3-1/4".10" rectangular duct joint on the top plate with 4 screws (2 pieces: removed in Step 4-1, the others: supplied). Then attach the supplied soft tape around the duct joint. ;In Case of 7" Round Vertical Discharge First, remove half-cut circular part of the top plate (duct knockout) using a hammer, pliers, etc. Mount the 7" round duct joint removed in step (1) with 4 screws. Then attach the supplied soft tape around the duct joint. CAUTION: • Wear working gloves to avoid injury. • Do not apply excessive force when removing the knockout. The fan may be damaged. Duct Joint Engage with the notches Cover Plate Hit dented points on the rectangular edge Duct Knockout Soft Tape Hit dented points on the circular edge Insert into the holes Duct Knockout 7" Round Duct Joint Duct Joint Soft Tape ;In Case of 3-1/4".....10" Horizontal Discharge First, remove half-cut rectangular part of the rear plate (duct knockout) using a hammer, pliers, etc. Mount ...