Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Air King Dateigröße: 291.05 kb Dateiname: 316488521en.pdf Unterrichtssprache:

Step 3 Step 3Step 3Step 3Step 3Step 3Remove the grease filters. Installing the hood Step 4 Step 4Step 4Step 4Step 4Step 4Remove the junction box cover. . . Remove either the top or the back wiring knockout according the preference and install an approved wiring clamp Step 5 Step 5Step 5Step 5Step 5Step 5Remove the duct knockouts using a flat blade screwdriver and a small hammer. Use the screwdriver by knocking out the pannel in similar fashion to a scalpel. Take care of sharp edges. Attention! Attention!Attention!Attention!Attention!Attention! If it is intended to use the hood in the recirculating version do not remove any duct knockouts and order the necessaruy charcoal filter from your supplier. . . . . . . . R1 R1R1R1R1 R1= Remove rectangular duct knockout only. R2 R2R2R2R2 R2 = Remove semicircular and rectangular duct knockouts. 1010101010 Step 6Step 6Step 6Step 6Step 6 For rFor rFor rFor rFor rectangular ducted discharge installations onlyectangular ducted discharge installations onlyectangular ducted discharge installations onlyectangular ducted discharge installations onlyectangular ducted discharge installations only (otherwise skip to next step) Attach exhaust adaptor/damperAttach exhaust adaptor/damperAttach exhaust adaptor/damperAttach exhaust adaptor/damperAttach exhaust adaptor/damper over knockout opening with two exhaust adaptor screws. Make sure damper pivotpivotpivotpivotpivot is nearest to top/back edgetop/back edgetop/back edgetop/back edgetop/back edge of hood. Remove tapetapetapetapetape from damper flap. ! NOTE:NOTE:NOTE:NOTE:NOTE: The exhaust adaptor/damper can be installed up to 1 inch on either side of the hood center to accommodate off-center ductwork. In extreme off- center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp. Step 7Step 7Step 7Step 7Step 7 For rFor rFor rFor rFor round ducted discharge installations onlyound ducted discharge installations onlyound ducted discharge installations onlyound ducted discharge installations onlyound ducted discharge installations only Re-install the rrrrround transitionound transitionound transitionound transitionound transition with its screws. NOTE:NOTE:NOTE:NOTE:NOTE: The round transition can be installed up to 1 inch on either side of the hood center to accommodate off-center ductwork. In extreme off- center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp. Step 8Step 8Step 8Step 8Step 8 Mark holesMark holesMark holesMark holesMark holes Select the vent option that your installation will require and proceed to that section: Outside top exhaustOutside top exhaustOutside top exhaustOutside top exhaustOutside top exhaust (Vertical duct– 3 1/4”x 10” Rectangular) Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots. !" #$%#& %$%#% #$%#& %$%#% ' & $()%$$ Outside top exhaustOutside top exhaustOutside top exhaustOutside top exhaustOutside top exhaust (Vertical duct–7” Round) Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots. !#$%#& %$%#% #$%#& %$%#% ' & (*+,-./0$- ' 1 Installing the hood 1010101010 Step 6Step 6Step 6Step 6Step 6 For rFor rFor rFor rFor rectangular ducted discharge installations onlyectangular ducted discharge installations onlyectangular ducted discharge installations onlyectangular ducted discharge installations onlyectangular ducted discharge installations only (otherwise skip to next step) Attach exhaust adaptor/damperAttach exhaust adaptor/damperAttach exhaust adaptor/damperAttach exhaust adaptor/damperAttach exhaust adaptor/damper over knockout opening with two exhaust adaptor screws. Make sure damper pivotpivotpivotpivotpivot is nearest to top/back edgetop/back edgetop/back edgetop/back edgetop/back edge of hood. Remove tapetapetapetapetape from damper flap. ! NOTE:NOTE:NOTE:NOTE:NOTE: The exhaust adaptor/damper can be installed up to 1 inch on either side of the hood center to accommodate off-center ductwork. In extreme off- center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp. Step 7Step 7Step 7Step 7Step 7 For rFor rFor rFor rFor round ducted discharge installations onlyound ducted discharge instal...

Herunterladen

Geben Sie zwei Ziffern: