Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
C12EF Slide the mounting rails into brackets. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. 5/81/25/81/2C13 C14 Mark position of screws by using holes as a template. 41941-01 3/29/2006 11 05-HF-012-EngS_3.29.06.indd 11 3/29/06 3:19:24 PM C17 C18 C19 C20 12 C15 C16 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. Tighten screws. Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Route wires through the strain relief. 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 12 3/29/06 3:19:27 PM C21 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground C22 Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option 13 Tighten the strain relief screws. Connect wires as shown. C24 I H G C23 Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 13 3/29/06 3:19:29 PM C25 I C26 J C27 ON OFF C28 14 Secure the motor by tightening the 2 screws. Turn on the power source. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Test the motor. If the motor does not run, check the plug connection. C29 E1 Go to step on page 17 to attach grille. 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 14 3/29/06 3:19:32 PM D11 EXISTING FAN F D12 15 Existing Construction – accessible only from below D13 2 1 D14 Route wires through strain relief. Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8 1/2”). Move the housing into position above the ceiling Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. F D15 Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into the joist. 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 15 3/29/06 3:19:35 PM 16 A 3 Pin 2 Pin Fan Motor Light Light Green Black Black White Black Black White White Bare Copper Ground D16 Main Switch 1 (AC In) *Option Fan & Main Light Together Switch 2 (AC In) *Option I D18 I D19 D20 J Connect wires as shown. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Secure the motor by tightening the 2 screws. G D17 H Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 16 3/29/06 3:19:37 PM 17 ON OFF D22 D23 E1 Go to step on page 17 to attach grille. D21 Test the motor. If the motor does not run, check the plug connection. Turn on the power source. Attaching the Grille Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. N F E1 K E2 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 17 3/29/06 3:19:40 PM 18 Install fluorescent bulb (Included). Align glass dome and push up. E7 P Screw finial into position. E5 M E6 O Attach thumbscrews. WARNING: To reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. N E4 Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Slide light fixture over posts. K E3 41941-01 3/29/2006 05-HF-012-EngS_3.29.06.indd 18 3/29/06 3:19:44 PM Trouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Light does not come on. Solution: • Replace the light bulb with a new bulb. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Fan is noisy. Solution: • Check and tighten all fasteners. • Check the glass to make sure it is secure. • Check the flapper to make sure it moves freely. If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at 41941-01 3/29/2006 19 05-HF-012-EngS_3.29.06.indd 19 3/29/06 3:19:44 PM Warranty Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust ...