Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
The control buttons are the light and speed controls (QuietMode™, Low and High). Refer to Figure 12. Figure 12 Light Control: Press button to turn on / off. Speed Control: Press button for speed. (QuietMode™, Low and High). Light Control Speed Control MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For optimal operation, clean range hood surface and stainless steel baffle filters regularly. Cleaning Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. Regular care will help preserve the appearance of the hood. 1) Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2) If hood looks splotchy (stainless steel hood), use an orange base cleaner to clean the surface of the hood. Avoid getting cleaner on the control switches. Spread a light coating over the surface of the hood and leave on for a few minutes. CAUTION: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub away stubborn spots. Use a slightly damp towel to get rid of any cleaning solution. Use dry soft towel to dry the hood. 3) To bring glow back into a stainless steel finish, use a stainless steel cleaner. 4) DO NOT allow deposits to remain for extended periods. 5) DO NOT use ordinary steel wool or steel brushes. Small bits of steel adhering to the surface may cause rust. 6) DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. 9 10 Cleaning Stainless Steel Baffle Filter CAUTION: DRAIN OIL BEFORE RESIDUE CAN OVERFLOW. 1. Grasp knob on baffle filter and push filter toward rear. 2. Gently pull each baffle filter down and discard oil and residue. 3. Wash baffle filters with warm soapy water. 4. Dry thoroughly and put back. NOTE: Baffle Filters are top rack dishwasher safe. Figure 13 Replacing Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1. Make sure all controls are OFF, and range hood is unplugged. 2. Place a flat-head screwdriver into the groove between the halogen light glass covering and the housing . 3. Gently separate glass covering from the housing . 4. Gently pull out the defective light bulb and discard. Light bulb should be 12V 20W maximum. 5. Wear a glove or use a cloth to hold the new light bulb and push securely into light socket. NOTE: DO NOT PUSH TOO HARD OR YOU MAY BREAK THE BULB CONNECTOR. 6. Put back halogen light glass cover . 7. Plug back power cord and turn on range hood to test for operation. 2 1 SPECIFICATIONS MODEL / SIZE CH8136SQB / 36” COLOR # 304 Commercial Grade Stainless Steel DESIGN 20-Gauge / Satin Finish FAN TYPE Squirrel Cage EXHAUST 6-1/4” Round Damper CONTROLS Three Speeds (QuietMode™, Low, High) HALOGEN LIGHTS 12V 20W x 2 HOOD DIMENSION (W x D x H) 35-1/4” x 19-3/8” x 11-1/4” DUCT COVER DIMENSION (W x D x H) 8-3/4” x 8-5/8” x 16”~31” WEIGHT (lbs) NET GROSS 37.4 44.0 SPEED QuietMode™ Low High Air Capacity (cfm) 250 450 600 Sone* 1.0 2.8 4.5 *In House Test Static Pressure “0”. One Sone is equivalent to the sound of a refrigerator at 40 decibels. **Specifications subject to change without notice. 11 MEASUREMENTS & DIAGRAMS *** All inch measurements are converted from millimeters. Inch measurements are estimated. 12 PARTS LIST MODEL NO.: CH8136SQB NO. DESCRIPTION MODEL / SIZE PART NO. 1 Duct Cover Bracket CH0061 2 Inner Duct Cover CH0595 3 Outer Duct Cover CH0596 4 6-1/4” Plastic Damper CY0187 5 Rubber Seal CH0539 6 Screws (3/16” X 3/8”) G3215 7 Back Casing CH0592 8 Blower Assembly 9 Screws (3/16” X 3/8”) G3398 10 Brackets CH0059 11 Hood Frame CH0040 12 Left / Right Side Trim CY0619/CY0620 13 Front Trim CH0044 14 Baffle Filters CH0594 15 Bottom Casing CH0591 16 Halogen Lights CY03341 17 Baffle Knobs CY0324 18 Electrical Box CY04751 19 Power Board CY0278 20 Capacitor 01475 21 Electrical Box Cover CY0475 22 Setup Board CH0048 13 14 MODEL NO.: CH8136SQB 1 2 3 4 5 6 7 8 14 15 12 18 19 20 21 22 10 9 13 16 17 11 15 Blower Assembly NO. DESCRIPTION MODEL / SIZE PART NO. 23 Screw (3/16” X 3/8”) G3231 24 Air Flow Grill CY0406 25 Right Locknut CY0382 26 Motor CY0519 27 Fixture Ring CY0572 28 Vent Plate CY0529 29 Left Blower CY0160 30 Left Locknut CY0365 31 Air Chamber CH0052 32 Right Blower CY0161 24 23 26 27 28 29 30 31 32 25 CIRCUIT DIAGRAM WHITE BLACK Transition Circuit AC 120V HALOGEN 60Hz LAMPS CAPACITOR MOTOR 12uF / 450V 16 DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arrival. Damages should be reported to carrier and a claim filed. Failure to do this could result in the carr...