Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
12. Repeat for all baffle filters and spacers. Refer to Measurements and Diagrams on page 21 for baffle filter and stainless spacer arrangement. 13. Install heating lamps (not provided), 120 Volts 175 Watts max. each. 14. Turn power ON in control panel. Check all lights and fan operation. 15. Make sure to leave this manual for the homeowner. Figure 16 Figure 17 OPERATING INSTRUCTIONS This KOBE hood is equipped with touch-sensor screen and features 3 minute delay shutoff, powerful centrifugal squirrel cage with baffle filters, bright 12-volt 20-watt halogen lights and heating lamp capability (heating lamps not included). The touch-sensor screen has Heat Lamp Control, Light Control, Speed Control (QuietMode™, Low, Medium and High), and Power Control. Refer to Figure 18. Power ControlLight Control Speed ControlHeat Lamp Figure 18 Power Control • ••••Once power is supplied to the KOBE hood, the sign will light up and remain lit as long as power is supplied to the hood. • ••••To activate, gently touch the symbol under the Power Control sign. The remaining control signs will light up and is ready for function choice. • ••••You can turn hood off immediately or after a 3 minute delay. Turn Off Immediately Gently tap the symbol under the Power Control sign twice, the range hood will turn off immediately leaving only the sign lit. 12 Turn Off After 3 Minute Delay Gently touch the symbol under the Power Control sign once, the symbol flashes and after 3 minutes, the hood will turn off leaving only the sign lit. Speed Control: • There are four speeds: QuietMode™, Low, Medium, and High. To activate the speed, touch the control under the speed sign. For example, if turning on hood at low speed, gently touch the symbol under the sign. If you want to switch from low to high speed, touch the symbol under the sign and the hood change to high speed. To turn off only speed control (if, for example, halogen lights are also on), touch the symbol under the sign. Light Control • ••••Gently touch the symbol under the sign once to turn on the light. Touch the symbol again to dim the lights. Touch the symbol a third time will turn off the halogen lights. Heating Lamp Control • ••••Gently touch the symbol under the sign once to turn on the heat lamps. Touching the symbol under the sign again will turn off heat lamps. 13 MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular care will help preserve the appearance of the hood. 1. Use only mild soap or detergent solutions. Dry surfaces using soft cloth. 2. If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood. 3. DO NOT allow deposits to accumulate or remain on the hood. 4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting. 5. DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. To Clean Baffle, Spacer, Filter, Oil Tunnel and Oil Container CAUTION: DRAIN OIL FROM BAFFLES, SPACER(S), FILTERS, OIL TUNNEL(S) AND OIL CONTAINERS BEFORE OIL AND RESIDUE CAN OVERFLOW. 1. Remove all baffles, spacer(s), filters, oil tunnel(s), and oil containers. Follow directions for installation in reverse. 2. Discard oil and residue. 3. Wash with warm soapy water. Dry thoroughly before replacing. (Note: Stainless Steel Baffles, Spacer(s) & Oil Tunnel are top rack dishwasher safe.) 14 To Replace Light Bulb CAUTION: HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. . . . . 1. Make sure all controls are off, and range hood is unplugged. 2. Place a flat-head screwdriver between light cover and housing . to remove cover . 3. Gently pull defective bulb straight out . and discard. Light bulbs should be 12V 20W maximum. 4. Wear a cotton glove or use a cloth to handle the replacement bulb (do not handle with bare fingers as this may shorten the life of the bulb). Push gently but securely into light socket. NOTE: DO NOT PUSH TOO HARD AS BULB “LEGS” MAY BREAK OFF. 5. Replace light cover . 6. Turn range hood ON to test for operation. 15 SPECIFICATIONS MODEL / SIZE CH0130SQB / 30” CH0136SQB / 36” CH0142SQB / 42” CH0148SQB / 48” DESIGN 18-Gauge Seamless Commercial Stainless Steel CONSUMPTION / AMPERE 702W / 5.85A – 30”, 36” 722W / 6.02A – 42”, 48”...