Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: GE Monogram Dateigröße: 320.65 kb Dateiname: d70d82c0-af36-49fd-8aff-ec1a9a68d0fd.pdf Unterrichtssprache:

The charts on the following pages show you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts. * IMPORTANT: If a rectangular-to- round transition adaptor is used, the bottom corners of the damper will have to be cut to fit, using the tin snips, in order to allow free movement of the damper. Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any hood. DUCTWORK REQUIREMENTS 6 Installation Instructions WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH DUCT PIECES EQUIVALENT NUMBELENGTH x USED R = TOTAL 31.4. x 10. Rect., straight 1 Ft. x ( ) = Ft. 7. Round, straight 1 Ft. x ( ) = Ft. 6. Round, straight 1 Ft. x ( ) = Ft. 31.4. x 10. Rect. 90° elbow 14 Ft. x ( ) = Ft. 31.4. x 10. Rect. 45° elbow 8 Ft. x ( ) = Ft. 31.4. x 10. Rect. 90° flat elbow 33 Ft. x ( ) = Ft. 31.4. x 10. Rect. wall cap with damper 24 Ft. x ( ) (18 ft. w/o damper) x ( ) = = Ft. Ft. 31.4. x 10. Rect. to 6. round transition 2 Ft. x ( ) = Ft. 31.4. x 10. Rect. to 6. round transition 90° elbow 4 Ft. x ( ) = Ft. 6. Round, 90° elbow 12 Ft. x ( ) = Ft. 6. Round, 45° elbow 7 Ft. x ( ) = Ft. Subtotal column 1 = Ft. MAXIMUM DUCT LENGTH: For satisfactory air movement, the total duct length of a 31.4. x 10. rectangular, 6. or 7. diameter round duct should not exceed 65 equivalent feet. DUCT EQUIVALENT NUMBER PIECES LENGTH x USED = TOTAL 6. Round 24 Ft. x ( ) = Ft. wall cap (18 ft. w/o with damper) x ( ) = Ft. damper 6. Round 33 Ft. x ( ) = Ft. roof cap 6. Round 2 Ft. x ( ) = Ft. to 31.4. x 10. rect. transition 6. Round 4 Ft. x ( ) = Ft. to 31.4. x 10. rect. transition 90° elbow 7. Round, 14 Ft. x ( ) = Ft. 90° elbow 7. Round, 9 Ft. x ( ) = Ft. 45° elbow 7. Round 28 Ft. x ( ) = Ft. wall cap (21 ft. w/o with damper) x ( ) = Ft. damper 7. Round 39 Ft. x ( ) = Ft. roof cap 7. Round 1 Ft. x ( ) = Ft. to 31.4. x 10. rect. transition 7. Round 5 Ft. x ( ) = Ft. to 31.4. x 10. rect. transition, 90° elbow Subtotal column 2 = Ft. Subtotal column 1 = Ft. Total ductwork = Ft. 7 Installation Instructions • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer. DAMAGE – SHIPMENT/INSTALLATION MOUNTING SPACE NOTES: • This range hood is for installation over ranges or cooktops up to 36. wide. • If you are going to vent your range hood to the outside, see the “Ducting Requirements” section for exhaust duct preparation. 66. or more from the floor to the top of the hood 30. or 36. 30. min. Bottom edge of cabinet needs to be 30. or more from the cooking surface PART QUANTITY Grease Filter only (JV338) 1 Charcoal Filter only 1 (JN327 and RN328) Grease Filter and Charcoal 2 Filter (JV347 and JV367) Mounting Screws 4 (8 - 18 x 3/4 Phillips pan head) Exhaust Adaptor 1 (for 31.4. x 10. rect. venting) Exhaust Adaptor Screw 1 (8 - 18 x 3/8 Phillips pan head or hex head) PARTS INCLUDED Flat blade and Phillips screwdrivers Pencil Metal snips (in some applications) Electric drillSaw (saber or keyhole) Duct tape Pliers LevelCaulking Tape measure TOOLS YOU WILL NEED 1/4. pivoting hex socket Flashlight Wire stripper 1/4. Nutdriver 8 1 Installation Instructions CHOOSE VENT OPTION Determine the vent option that your installation will IMPORTANT: If the hood is to be installed in a require and that is available for your model from the recirculating, non-vented ductless manner, do not below choices. knock out any vent openings in the hood. Only an electrical access hole will be knocked out of the hood. Outside top exhaust (Vertical duct–31.4. x 10. Rectangular) Outside rear exhaust (Horizontal duct–31.4. x 10. Rectangular) Outside top exhaust (Vertical duct–7. Round) A C B Recirculating (non-vented/ductless) D JV338 JV347 JV367 JV338 JV347 JV367 JV338 JV347 JV367 JN327 RN328 JV347 JV367 9 Installation Instructions REMOVE EXHAUST ADAPTOR If exhausting/venting using the 31.4. x 10. rectangular duct—optional for JV338, JV347 and JV367 models Remove the exhaust adaptor from the inside of the hood. Set it aside along with its mounting screws. 31.4 x 10 rectangular exhaust adaptor and screws 2 REMOVE FILTER Remove the shipping tape holding the metal grease filter in place. Pull down on the center of the front edge of the filter. The filter will then slip out of the retaining tabs on the back. 3 Metal grease filter REVERSE THE BAFFLE FOR DUCTED INSTALLATIONS ONLY (JV347 and JV367 models) If the hood is to be recirculated, skip to the next step. Remove the baffle from the top of the hood. Re-install the baffle so the short side marked “VENTED” is visible. The long side of the baffle should be inside the hood. 4 “VENTED” is visible 5 REMOVE WIRING COVER...

Herunterladen

Geben Sie zwei Ziffern: