Stimmen - 0, Durchschnittliche Bewertung: 4 ( )

Hersteller: NuTone Dateigröße: 1.26 mb Dateiname: 04307655.pdf Unterrichtssprache:

fig.2 WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug 33-7/16" (85cm) max must be plugged into an outlet that is properly fig.3 installed and grounded. WARNING - Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance. Set the electrical power supply within the space covered by the decorative flues. Position the power socket at a maximum distance of 33-7/16” (850 mm) from where the lead exits from the hood (see illustration alongside). Make sure this does not interfere with the bracket fastening area or with the decorative pipe (where the flue touches the wall). Fit the plug into the power socket. 5 6 DISCHARGE COLLAR 6” DIAMETER DUCT DUCT CONNECTOR INSTALL FLUE MOUNTING BRACKET DUCTED AND NON-DUCTED 1. Assemble the flue mounting bracket, adjusting outside width as shown. Fig.5 2. Carefully center the mounting bracket directly over the range hood location. 3. Secure the bracket assembly to the ceiling using (2) 4.8x38mm mounting screws and drywall anchors. Make sure the bracket is pushed into the corner, tight against the wall and centered over the hood. FLUE MOUNTING BRACKET 7 - 3/4” (197mm) 3.9 x 6mm FLAT HEAD BRACKET SCREWS INSTALL MOUNTING BRACKET 1. Construct wood wall framing that is flush with interior surface of wall studs. Make sure: a) the framing is centered over installation location. b) the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown. 2. After wall surface is finished, secure mounting bracket to framing using dimensions shown. NOTE: - On 8’ ceilings, the hood distance above cook top is : minimum 24”, maximum 28” (for Ducted Configuration). minimum 24”, maximum 27” (for Non-Ducted Configuration). - On 9’ ceilings, the hood distance above cook top is : - minimum 28”, maximum 30” (the air vents on the upper flue will be exposed after installation). FRAMING BEHIND DRYWALL 36 3/4"= bottom of hood 24" above cooktop 42 3/4"= bottom of hood 30" above cooktop 36 3/4” to 42 3/4” above cooktop fig.4 fig.5 PREPARE THE HOOD Note: On stainless steel hoods, carefully remove the plastic protective film from all exterior surfaces of the hood and decorative flues, prior to final installation. DUCTED CONFIGURATION 1. Install the discharge collar into the duct connector of the range hood. Fig.6 fig.6 2. Attach an adequate length of 6” round steel ducting to the range hood duct connector. Fig.6 3. Duct tape all joints to make them secure and air tight. 4. Carefully place the lower decorative flue into the recessed area of the range hood top. Fig. 7 5. Carefully slide the upper decorative flue down inside the lower flue. Fig. 7 fig.7 UPPER FLUE LOWER FLUE UPPER FLUE VENTS EXPOSED UPPER FLUE VENTS CONCEALED PREPARE THE HOOD NON - DUCTED CONFIGURATION Note: The following materials must be purchased separately for non-ducted recirculation installations. • 5” diameter expandable / flexible aluminum duct. • 1/16” diameter twist drill. CAUTION: Do not use plastic or rigid metal ducting. 1. Discard discharge collar and damper supplied with the hood. Install the 5” to 6” adapter (supplied). 2. Measure the distance “A” 3. Attach aluminum flexible duct to the 5” adapter. Tape all joints with duct tape. Fig.8 4. Assemble the recirculation plenum to the flexible duct. Fig.8 5. Drill three (3) 1/16” diameter equally spaced holes through the duct and duct connector of the recirculation plenum. Fig.8 6. Secure duct to the plenum’s connector with (3) sheet metal screws. Tape all joints with duct tape. Fig.8 A PLENUM (3) SCREWS 5” ALUMINUM FLEX DUCT 5” 6” ADAPTER BLOWER COLLAR fig.8 7 PREPARE THE HOOD NON - DUCTED CONFIGURATION, cont’d. 8. Carefully place the lower decorative flue into the recessed area of the range hood top. Fig.7 9. Carefully slide the upper decorative flue down inside the lower flue. Note: air vents must be up. Fig.7 10.Secure the recirculation plenum to the upper flue with (4) flat head screws. Fig.9 INSTALL THE HOOD Note: at least two people will be required to mount the hood. 1. Raise the hood into its HEIGHT mounting position. 2. Plug the power cord into the electric wall receptacle. Tuck excess cord behind the flue. 3. Align the rectangular opening on the back of the hood with the wall- mounting bracket. Gently lower the hood ...

Herunterladen

Geben Sie zwei Ziffern: