Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Do not use to exhaust hazardous or explosive materials and vapors. 2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 3. For best capture of cooking impurities, your range hood should be mounted so that the top of the hood is 24-30” above the cooking surface. 4. Please read specification label on product for further information and requirements. Installer: Leave this manual with the homeowner. Homeowner: Operating and Cleaning information on page 6. NOTE If hood is to be installed Non-Ducted: Purchase a set of (2) non-ducted filters from your local distributor or retailer and attach them to the aluminum mesh filters. TABLE OF CONTENTS This manual is divided into sections as follows: “PREPARE HOOD LOCATION” Run ductwork from roof or wall cap, and electrical wiring from service panel - to installation location “PREPARE THE HOOD” Get your hood ready for installation “CONNECT WIRING” Make electrical wiring connections to hood “INSTALL HOOD” Secure hood to cabinet and ductwork - install bulbs and filters “OPERATION” How to use the hood controls “CLEANING” Keep your hood in top working condition “SERVICE PARTS” Part numbers and exploded view of hood components “WARRANTY” One-year limited warranty and how to contact us 4 Nülöne ALLURE® WS3 SERIES RANGE HOOD PREPARE HOOD LOCATION Page 2 PREPARE HOOD LOCATION ROOF CAP V 31/4" X 10" or 7" ROUND DUCT (For vertical discharge) 24" - 30" ABOVE COOKING SURFACE HOUSE WIRING (Top or Back of hood) WALL CAP 3/" X 10" DUCT (For horizontal discharge) |^| Determine whether hood will discharge vertically (3%” x 10” or 7” Round), or horizontally (3W x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows. \^\ Use diagrams, below, for proper placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. HOOD MOUNTING SCREWS (4) 1315/16" (30" hood) 31/4” X 10” VERTICAL DUCTING (30" hood) (36" hood) (42" hood) WOOD SHIMS (recessed-bottom cabinets only) WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) 31/4” X 10” HORIZONTAL DUCTING CABINET FRONT ^1,1 k 1 /8" %" r 3%" caBinet-*- BOTTOM HORIZONTAL DUCT ACCESS HOLE -5/- _1315/16" (30" hood) 1615/16" (36" hood) 1915/16" (42" hood) HOOD MOUNTING SCREWS (4) ? CENTER LINE 5/'"-*| - 7/"- -1315/16" (30" hood)-1615/16" (36" hood) 1915/16" (42" hood) ELECTRICAL ACCESS HOLE (in wall) HOOD MOUNTING SCREWS (4) 1315/16" (30" hood) 1615/16" (36" hood) "1915/16" (42" hood) " 7” ROUND VERTICAL DUCTING r CABINET FRONT 1315/16" (30" hood) 1615/16" (36" hood) ' 1915/16" (42" hood) 101/2" WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL t ACCESS HOLE (in cabinet bottom) Run house wiring between service panel and hood location. PREPARE THE HOOD |^| Remove 7” Round Duct Plate from top of hood. Set duct plate aside - with mounting screws. Remove tape holding Filters in place. Pull down on filter tabs or finger holes and lift filters out. Set filters aside. Nülöne ALLURE® WS3 SERIES RANGE HOOD Page 3 PREPARE THE HOOD PREPARE THE HOOD S Remove Teflon®-coated bottom cover from hood. Set cover and mounting screws aside. Teflon® is a registered trademark of DuPont. TEFLON®-COATED BOTTOM COVER (Held in place with 2 screws) □ Remove Damper/Duct Connector from inside the hood. Set connector aside - with mounting screws and parts bag. DAMPER/ DUCT CONNECTOR Remove either top or back wiring knockout and install approved Electrical Cable Clamp ELECTRICAL CABLE CLAMP LIGHT PANEL Non-Ducted Installation - Skip to Step 15. (3) #8 SCREWS The following Steps (6 thru 14) are for DUCTED INSTALLATION ONLY. Remove Light Panel - held in place with (3) #8 screws and (2) #8 screws. Disconnect light assembly wire harness (white connector). AIR CHUTE Remove Air Chute - held in place with one (1) screw. NOTE: Be careful not to disconnect any wires. (3 Remove Baffle from air chute. Rotate baffle. Reinsert baffle into air chute (as shown) so that baffle tabs fit all the way into slots in air chute. An audible “click” will be heard when fully installed. This will close off the air flow through the non-ducted slots on top o' hood. Re-install air chute, re-connect wire harness, and replace light panel. NOTE: Be careful not to trap wires between support fin and light panel. SUPPORT FIN Nülöne PREPARE THE HOOD ALLURE® WS3 SERIES RANGE HOOD Page 4 PREPARE THE HOOD TOP RECTANGULAR DUCT KNOCKOUT (Remove for 314”x 10” Vertical & for 7” Round Discharge) TAPE SEMI-CIRCULAR DUCT KNOCKOUT (Remove for 7” Round Discharge) REAR RECTANGULAR DUCT KNOCKOUT (Remove for 314”x 10” Horizontal Discharge) [11 Remove appropriate Duct Knockout(s) from top ...