Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel. Lock or tag service panel to prevent power from being switched on accidentally. 3. Installation work and electrical wiring (including switch location) must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. 4. Provide sufficient air for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the combustion equipment standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local codes. 5. This product may have sharp edges. Be careful to avoid cuts and abrasions during installation and cleaning. 6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 7. Ducted fans must always be vented to the outdoors. 8. Use only metal ductwork. 9. Do not use this fan with any solid-state speed control device. 10. As an alternative, this product may be installed with the UL- approved cord kit designated for the product, following instructions packed with the cord kit. 11. This unit must be grounded. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 1. Never leave greasy cooking unattended. Oil, butter, lard, etc. can ignite in a few minutes. 2. Always turn hood ON when cooking at high heat or when cooking flaming foods. 3. Always use cookware appropriate for the size of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:* 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN — You may be burned or spread the fire. 3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result. 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you already know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA. caution 1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. For best capture of cooking impurities, range hood should be mounted so that the top of the hood is 24”-30” [or applicable dimension depending on hood height and test height] above the cooking surface. 3. Read specification label on product for information and requirements. NOTE If hood is to be installed non-ducted: Purchase a set of (2) non-ducted filters from your local distributor or retailer and attach them to the aluminum mesh filters. Installer: Leave this manual with the homeowner. Homeowner: Cleaning, Maintenance and Operating instructions on page 2. cleaning & Maintenance For performance, appearance, and health reasons, clean filter, fan and grease-laden surfaces. Use only a clean cloth and mild detergent solution on stainless and painted surfaces. Clean all- metal filters in the dishwasher. The motor is permanently lubricated and never needs oiling. If the motor bearings make excessive or unusual noise, replace the motor with the exact service motor. The impeller should also be replaced. Use 120 V, 50 W, shielded halogen bulbs - MR16 with GU10 base. Purchase bulbs separately. The grease filters, bottom panel, and blower wheel should be cleaned frequently. Use a warm detergent solution. The grease filters and blower wheel are dishwasher safe. Note: Some minerals, when in contact with dishwasher soap additives, may cause filters to discolor. This discoloration is not covered by the warranty. To remove blower wheel: Pull wheel straight down and off of motor. When reinstalling blower wheel, make sure tab on wheel fits into one hole on motor. prepare hood location SOFFIT24" - 30" ABOVECOOKING SURFACECABINET3." X 10" DUCT(For horizontal discharge) WALL CAPROOF CAP3." X 10" or7" ROUND DUCT(For verticaldischarge) HOUSE WIRING(Top or Back of hood) HOODHOOD tab 1 Determine whether hood will discharge vertically (3.” x 10” or 7” Round), or horizontally (3.” x 10” only). For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows. 2 Use the proper diagram below, for placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. * Note the extra wood shim and mounting screw near the cabinet front, 2-3/8” to the ri...